Prior To Use; Lighting The Grill Burner; Checking For Gas Leaks - Campingaz 2 Series Classic L Benutzung Und Wartung

IFU 4010026500 - 2 Series - version finale.qxp
- tighten the G1/2 threaded nut on the hose onto the
barbecue inlet connector and the M20x1.5 threaded nut
onto the regulator output connector following the
instructions supplied with the flexible hose.
- use a spanner to hold the barbecue inlet connector firm and
tighten or loosen the threaded nut with another spanner.
- use a spanner (14) to hold the regulator outlet connector
14
- check for leaks following the instructions in paragraph f).
Check that the flexible hose stretches out normally without
twisting or pulling and does not come into contact with the hot
sides of the barbecue. It should be replaced when the expiry
date on the hose is passed or whenever it is damaged or
develops surface cracks.
Belgium, Luxembourg, U nited Kingdom, Ireland,
Portugal, Spain, Italy, Croatia, Greece, N etherlands,
Czech Republic, Slovakia, H ungary, Slovenia, N orway,
Sweden, Denmark, Finland, Bulgaria, Turkey, Romania,
Poland:
The barbecue is equipped with a circular connector. It should
be used with flexible hose that is suitable for use with butane
and propane gas. H ose length should not exceed 1.20 meters.
It should be replaced if it is damaged or cracked, when required
by national regulations or at the end of the part lifecycle. D o
not pull or pierce the hose.
Keep the hose away from any parts of the barbecue that get
hot. Check that the flexible hose stretches out normally,
without twisting or pulling.
Switzerland, Germany,Austria:
The barbecue should be used with flexible tubing that is
suitable for use with butane and propane gas. Tubing length
should not exceed 1.50 meters. D o not pull or pierce the
tubing. It should be replaced if it is damaged or cracked, when
required by national regulations or at the end of the part
lifecycle. D o not pull or pierce the tubing. Keep away from any
parts of the barbecue that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
Flexible tubing connection: To connect the tubing to the
connector on the barbecue, tighten the nut on the tubing firmly
but without excess force using the two wrenches provided:
- no. 10 wrench to tighten the connector
- no. 17 wrench to tighten the nut on the tubing
10
- check for leaks following the instructions in paragraph f).
e) Lid
H andle the lid carefully, especially during operation. D o not lean
over the base
f) Checking for gas leaks
1) W ork outside, away from all sources of ignition. D o not
smoke.
10/10/2013
2) Make sure the control knobs are in the "off" (
3) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip.
4) Fit the regulator onto the gas cylinder in accordance with
its instructions.
5) Use a gas leak solution to test for leaks.
use a naked flame to check for gas leaks.
firm. 6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain closed: off
O
position ). O pen the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are gas
leaks.
8) The leak can be stopped by tightening any hose connection
or replacing any faulty component. The barbecue must not
be used until the leak is stopped.
9) Close the valve on the gas cylinder. Check for leaks at least
once per year and each time the gas cylinder is replaced.
g) Prior to use
N ever use the barbecue until the instructions have been read
carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked
- the hose does not
touch
components
may get hot.
- that the ventilation openings in the gas receptacle housing are
not obstructed, if appropriate.
Check that the venturi tubes (VT ) cover
the injectors (IJ ).
h) Lighting the grill burner
Read steps 1 to 6 before beginning with step 1.
N ever light the barbecue with the lid closed, only
1)
with the lid open.
2) Make sure the 2 control knobs are in the "off" (
3) O pen the gas cylinder valve.
4) Press one of the 2 control knobs and turn it to the
flame
(
button ( ) until you hear the click. Repeat 3 or 4 times if
11
12:00 Page 11
O
Important:
any
which
) position, then immediately press the igniter
) position.
GB
never
O
) position.
full