Preparation For Operation - GRAPHITE 58G960 Betriebsanleitung

GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service tel. +48 22 573 03 85
Ul. Pograniczna 2/4 fax. +48 22 573 03 83
02-285 Warszawa e-mail graphite@gtxservice.pl
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna
gtxservice.pl
GRAPHITE zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi. Pełna oferta części
i usług na gtxservice.pl.
Zeskanuj QR kod i wejdź na gtxservice.pl
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
RECIPROCATING SAW
58G960
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
• Use dust-masks when cutting to protect your respiratory system
against produced dust.
• Carefully check the processed material before cutting to eliminate
possibility of cutting nails, bolts, or other hard objects.
• Do not cut objects thicker than allowed in technical specification
for a given material.
• Prior to operation check if there is enough space under processed
material to avoid table or floor damage with the blade.
• Hold the saw with both hands.
• Ensure the saw blade does not have contact with the material
before pressing the switch.
• Do not touch moving parts with your hand.
• Before cutting floor, wall or other material make sure it does not
contain electrical wires.
• Do not put away the saw until it stops moving. Do not switch the
saw on when not holding it with your hand.
• To remove the blade, first switch the saw off with the switch and
wait until the blade stops moving. Disconnect the saw from power
supply.
• Do not touch the blade or processed material immediately after
the work has been finished. Those elements may be hot and may
cause burns.
• When you see unusual behaviour of the tool or hear strange
noises, immediately switch off the tool and remove the plug from
mains socket.
• To ensure proper cooling keep ventilation holes in the saw body
uncovered.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
do napraw gwarancyjnych
na platformie internetowej
small risk of operational injuries.
CONSTRUCTION AND USE
Reciprocating saw is a hand-held power tool with insulation class
II. It is driven by a single-phase commutator motor. The tool is
designed for making straight, coarse cuts, curved cuts and holes
in wood, wood-based materials, plastics and metals (provided that
appropriate blade is used). Range of use covers repair and building
works, and any work from the range of individual, amateur activities
(tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Blade
1.
Blade holder
2.
Switch lock button
3.
Switch
4.
Footplate
5.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Transport case - 1 pce
1.

PREPARATION FOR OPERATION

BLADE INSTALLATION
Disconnect the power tool from power supply.
Installation and removal of the blade is toolless.
• Turn the ring of the blade holder (2) and slide the blade into the
holder until it stops (fig. A).
• Release the ring of the blade holder (2) (the ring will return to the
default position).
• Pull the blade lightly to make sure it is properly fixed.
If the ring of the blade holder does not return to the default
position, turn the ring manually.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the saw rating plate.
Switching on – press the switch button (4).
Switching off – release pressure on the switch button (4).
Locking the switch (continuous operation)
Switching on:
• Press the switch button (4) and hold in this position.
• Press the switch lock button (3).(fig. B).
• Release pressure on the switch button (4).
Switching off:
• Press and release the switch button (4).
Work speed is controlled within its range with pressure on the switch
button (5).
7