Maintenance - Oxyturbo OXYLASER IRON Gebrauchs- Und Wartungsanleitung

direction.
- Light the gas immediately at the burner, with a match or
a lighter.
3.2 ADJUSTMENT
- The flame is adjusted by turning the adjusting knob (4).
3.3 PUTTING OUT
- Turn the adjusting knob (4), clockwise until completely
closed.
3.4 ACCESSORIES
- Make sure the blowlamp valve is closed, turn the
adjusting knob (4) clockwise.
- Unscrew the burner in an anticlockwise direction (fig.4).
- Mount the desired burner screwing down hand tight
only.
- Mount the desired accessory screwing down hand tight
only.
- Check the seal (see 5.2).
i
CAUTIONS
• Use the blowtorch in a horizontal position
• The blowlamp must be used in a well-ventilated area,
away from inflammable materials or substances. Fire
hazard!
• Once the blowlamp is lit, let it warm up for 30
seconds. If the blowlamp is not completely warmed up
or moved brusquely it may flare up. If this happens,
keep the blowlamp in a vertical position for a few
seconds.
• When lit the blowlamp should never be left
unsupervised.
• The blowlamp must always be placed at a safety
distance from walls or other objects.
• Work on a non - inflammable base.
• During welding works wear goggles and gauntlets.
• Attention! Avoid breathing welding fumes.
• Avoid the accumulation of heat on the blowlamp
when the flame is brought too near the object to be
heated.
• During use, parts of the blowlamp can reach high
temperatures. After putting it out let it cool before
handling.
• It is dangerous to use damaged or incorrectly
functioning equipment.
• In case of gas delivery problems, check there is gas
in the cartridge (see 5.4). If so, the problem could be
resolved by cleaning the injector (see 5.5).
• If the piezoelectric device presents faults, check the
ignition electrode (see 5.6).
4. STORAGE
- Replace the blowlamp in its wrapping or in its box) and
store it in a cool, dry, and well ventilated place.
i
CAUTIONS
When the cartridge is inserted in the blowlamp
• Protect from sunlight.
• Do not expose to temperatures greater than 50° C.
• Keep out of the reach of children.

5. MAINTENANCE

• Do not carry out maintenance or repairs, other than
the following.
• Use only original OXYTURBO spare parts and
accessories.
• Spare parts are available from your retailer.
• In case of failures which cannot be repaired following
these instructions, take your blowlamp back to the
retailer.
5.1 GAS LEAKS
- If your appliance leaks gas (gas smell) take it outdoors
immediately to a well ventilated area, away from
inflammable sources where the seal can be checked.
5.2 CHECKING THE SEAL
- To check the seal of the blowlamp, work outdoors and
do not use a flame: use soapy water or special detectors
(Gascontrol cod. 405020).
- Spray the detector on the area to be checked.
- Gas leaks are detected by the formation of bubbles or
foam.
5.3 CHANGING THE GASKET
- Remove the worn gasket from its seat.
- Insert the new gasket into the seat by pushing its edges
down with a flat screwdriver paying attention not to
damage it.
5.4 CHECKING THE CARTRIDGE CHARGE
- Make sure the blowlamp valve is closed, rotate the
adjusting knob (4) clockwise.
- Shake to check if the noise of the liquid gas can still be
heard.
5.5 INJECTOR CLEANING
- Unscrew the burner in an anticlockwise direction.
- Remove the injector with a hexagonal spanner.
- Clean the injector by blowing through the hole.
- Re-fit the injector and screw it down well. Check the seal
(see 5.2).
- Remount the burner.
i
CAUTIONS
• Do no use needles or pins to clean the injector, damage
could result making the blowlamp dangerous.
• If the blockage cannot be removed, substitute the
injector.
5.6 CHECKING THE PIEZOELECTRIC IGNITION
ELECTRODE
- Make sure the distance between the electrode and the
burner is between 4 and 6 mm.
N.B.Some of the details in the illustrations may differ from
those of the appliance supplied. This company reserves the
right to modify the product without prior warning.
13