Plantronics P820-M Kurzanleitung Seite 3

FCC Requirements Part 15
DECLARATION OF CONFORMITY
We Plantronics, 345 Encinal Street Santa Cruz, California, 95060 USA (800) 544-4660 declare under
our sole responsibility that the products P820, P820-M, P830, and P830-M comply with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC REGISTRATION INFORMATION — Part 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA.
On the exterior of this equipment is a label that contains a product identifier in the format
US:AAAEQ##TXXXX. If requested, this information must be provided to your telephone company. A
plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to
a compatible jack that is also compliant. See installation instructions for details. The REN is useful
to determine the quantity of devices you may connect to your telephone line. Excessive RENs on a
telephone line may result in the devices not ringing in response to an incoming call. In most, but not
all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices
you may connect to your line, as determined by the REN, contact your local telephone company. For
products approved after August 8, 2001, the REN for this product is part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without the decimal
point. (For example, 03 represents a REN of 0.3.) For earlier producers, the REN is separately shown on
the label. If this telephone equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. But if advance
notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will
be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone
company may make changes in its facilities, equipment, operations, or procedures that could affect
the proper functioning of your equipment. If they do, you will be notified in advance in order for you
to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this
unit, for repair or warranty information, please contact customer service at (800) 544-4660. If the
equipment is causing harm to the network, the telephone company may request that you disconnect
the equipment until the problem is resolved.
DO NOT DISASSEMBLE THIS EQUIPMENT: it does not contain any user-serviceable components.
We recommend the installation of an AC surge arrester in the AC outlet to which this equipment is
connected. Telephone companies report that electrical surges, typically lighting transients, are very
destructive to customer terminal equipment connected to AC power sources.
Exposure to RF Radiation
The internal wireless radio operates within the guidelines found in radio frequency safety standards
and recommendations, which reflect the consensus of the scientific community. Independent studies
have shown that the internal wireless radio is safe for use by consumers. Visit plantronics.com for
more information. In order to comply with FCC RF Exposure requirements, the base must be installed
and operated such that a minimum separation distance of 20 cm is maintained between the base and
all persons during normal operation. The Microphone Clip complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
NOTE: Modifications not expressly approved by Plantronics, Inc. could void the user's authority to
operate the equipment.
Industry Canada Regulatory Information
This product meets the applicable Industry Canada technical specifications/Le présent materiel est
conforme aux specifications techniques applicable d' Induristrie Canada.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du Canada.