Peg Perego Booklet 50 Gebrauchsanleitung Seite 20

in the figure.
12 It can be adjusted into 2 positions:
POSITION 1: to use
POSITION 2: to attach the car seat
13 To remove the front bar, press down on the buttons from
both sides, as per the sequence shown and remove (fig_a).
It is possible to open the front bar on one side only, so as to
facilitate the child's entry and exit (fig_b).
WARNING: The front bar has not been designed to
support the child's weight; the front bar has not been
designed to lift the seat with the child's weight. The
front bar does not replace the seat belt.
14 Before releasing the armrest, unfasten the elastic from
the cover on both sides.
15 Slightly close the chassis.
Rotate the armrest to unfasten it from the cap, as
shown in figure (fig.a).
To completely remove the armrest, pull it outwards
on both sides (fig.b).
Finally reattach the cover elastics to the chassis.
16 Chassis without armrests. Keep the armrests for a
future use.
17 To reattach the armrests, proceed in reverse sense.
Pay attention to the attachment direction.
When attaching the armrest, keep an eye on the
button, because it must be in front of the armrest and
not behind, as shown.
Attach the armrests to the chassis as shown.
18 FIXED OR SWIVELING FRONT WHEELS: Lift the levers
to prevent the wheels from swiveling (fig_a) and
lower them to allow the wheels to swivel (fig_b). On
uneven surfaces, the wheels should be set to their
fixed position.
19 BRAKE: Press the lever down to apply the brake on the
chassis and lift it to release the brake.
20 ADJUSTABLE HANDLEBAR: To adjust the height of the
handlebar, press both of the side buttons at the same
time (fig_a) and swing it into the desired position
(fig_b), then release the buttons.
21 FOOTREST: before adjusting the foot rest, ensure its
cover is accurately fitted; if it isn't, fit it accordingly. To
lower the footrest push the two levers downwards and
then push the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
It can be adjusted into several positions.
22 ADJUSTING THE BACKREST: to lower the backrest,
press the clip and the backrest will move down to the
desired position.
To raise the backrest, press the clip and lift the
backrest to the desired height.
23 FOOT MUFF: Lift the leg rest, slide the foot muff over
and button it below (fig_a), then slide the foot muff
under the front bar (fig_b). Unbutton the internal
button on the hood on both sides (fig_c) and button
up the foot muff (fig_d).
24 FIVE POINT SAFETY HARNESS: to fasten it, push the two
waist strap buckles (with the shoulder straps attached
– arrow_a) into the leg divider until they click into
place (arrow_b). To unfasten it, press the round button
in the centre of the buckle (arrow_c) and pull the waist
straps out (arrow_d).
25 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, move it
in the opposite direction.
To adjust the height, slip the belts through the eyelet
in the fabric (fig_b) and position them in the most
suitable eyelet.
The seat belts are fitted with shoulder pads and
crotch straps (fig_c).
26 FOLDING UP: To fold up the stroller, we recommend
ensuring the front wheels swivel, closing the hood,
removing the car seat when fastened.
Align the handlebar and frame as shown in the figure
(fig_a).
Rotate the safety lever to the left (fig_b) and pull the
internal handle towards yourself (fig_c).
27 Allow the handlebar to fall in on itself until fully
folded (fig_d).
The frame is folded correctly when the side fastener
automatically locks (fig_e). Otherwise, gently press
down on the frame (fig_f).
The stroller is free-standing when folded.
28 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull the pivot outwards and
remove the wheel as shown in the figure (fig_a).
To remove the front wheels: press the tab as shown, and
remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
29 REMOVABLE ITEMS: to remove the hood, take the
elastic off from the buttons on the inside of the
handlebar (fig_a), detach the press studs the sides of
the chassis (fig_b), detach the Velcro strip from the
backrest (fig_c) and remove the attachments of the
hood from their positions on the chassis (fig_d).
30 To remove the seat fabric, press in the holes on the
inside of the chassis (fig_a); remove, from the side of
the seat, the rigid flap of the chassis fabric ((fig_b),
unfasten the elastic of the net from the side buttons
inside the handlebar (fig_c) and unfasten the elastics
from the buttons inside the chassis (fig_d).
31 From the front, remove the lining from the foot
platform (fig_a), remove the leg divider strap from
under the seat (fig_b), unbutton the seat fabric (fig_c),
unscrew the waist belt on the side (fig_d) and remove
the seat fabric from the backrest (fig_e).
GANCIOMATIC SYSTEM
The Ganciomatic System offers a fast, practical means
of fastening a Primo Viaggio car seat (up to 13 kg
of weight, sold separately) to the stroller, using the
Ganciomat attachments.
32 GANCIOMATIC HOOKS ON THE STROLLER: to lift the
stroller's Ganciomatic hooks, pull back the fabric at the
corners of the seat.
Lift the two Ganciomatic hooks which will
automatically move outwards.
_ To lower the hooks, proceed in the opposite order.
33 Booklet 50/50 S + Primo Viaggio
To fasten the car seat to the stroller:
_ Lock the stroller brakes;
_ Lift the stroller's Ganciomatic hooks:
_ Extend the front bar into position 2 (see point 12).
_ If in place, remove the hood from the stroller and fully
lower the backrest. Once the seat has been fastened,
lift the backrest to the maximum height .
_ Position the car seat, mum-facing, on the Ganciomatic
hooks and press down until they click.
_ To release the car seat from the stroller please read the
instructions book
BOOKLET 50/50 S + PORTE ENFANT
34 It is possible to use and pair the PegPerego Porte
Enfant with the Booklet 50/50 S stroller. For
installation, see the Porte Enfant instruction manual.
SERIAL NUMBERS
35 Information about the production date can be found
on the Booklet 50/50 S .
_ The product name, production date and serial number
of the chassis.
This information is required for any complaints.
THE ORIGINAL ACCESSORY
PEG-PÉREGO
Peg-Pérego accessories are designed as a useful,
practical means of simplifying the lives of parents.
Discover all your product's accessories on
www.pegperego.com
- 20 -