TABLE OF CONTENTS SECTION I. STANDARD EQUIPMENT ..................1 SECTION II. SAFETY Safety Instructions ................... 2 SECTION III. CE DECLARATION OF CONFORMITY ..............6 SECTION IV. MACHINE SPECIFICATIONS ...................7 SECTION V. SET UP & OPERATING PROCEDURES Mounting Machine To Table ................8 Saw Blade Installation ..................
SECTION II Read the Following thoroughly before proceeding ALWAYS WEAR PROTECTIVE EQUIPMENT: Since 1883, EH Wachs has built a reputation for qual- ity and a commitment to consumer satisfaction. In accor- WARNING dance with this, Wachs must take on the added responsi-...
Seit 1883 hat EH Wachs seinen Ruf für Qualität und Zufriedenstellung seiner Kunden aufgebaut. Wachs übernimmt demgemäß die Depuis 1883, la société EH Wachs a bâti sa réputation sur la qualité de ses produits et son engagement à satisfaire la clientèle.
INSTRUÇÕES DE SEGURANÇA TURVALLISUUSOHJEET Já desde 1883 que a EH Wachs tem vindo a criar uma reputação de qualidade e um compromisso de satisfação dos EH Wachs on tunnettu korkeasta laadusta ja tyytyväisistä asiakkaistaan jo vuodesta 1883. Wachs huolehtii myös siitä, että...
Seite 7
ANVISNING I SIKKERHED Siden 1883 har EH Wachs haft ry for deres kvalitet og varetagelse af kundtilfredshed og vil også gøre vort bedste for at sikre, at vore maskiner benyttes på en sikker og forsvarlig måde. Vi har lavet en liste over påmindelser, der skal bidrage til at skabe det sikrest mulige arbejdsmiljø. Vi anbefaler, at sikkerhedsforanstaltningerne på...
TUBE CUT OFF SAW TC 4.5 CE DECLARATION OF CONFORMITY SECTION III Name and address of manufacturer (if different) E.H. Wachs Company 100 Shepard St. Wheeling, Il. 60090 USA Distributed in the EC by: Business address: We declare that the machine described below conforms with the EHSR of the machinery directive 89/...
TC 4.5 SETUP & OPERATING PROCEDURES SECTION V Mounting Machine to Table TC 4.5 has mounting clamps installed. Place saw on edge of table and secure 2 ½ -13 HHCS with 3/4” wrench. For permanent installation, remove mounting clamps by loos- ening the 2 ½-13 HHCS with 3/4”...
TUBE CUT OFF SAW TC 4.5 TC 4.5 SETUP & OPERATING PROCEDURES (CONT.) SECTION V Workpiece Clamping Machining Instructions To open vise, rotate vise handle counter clock- CAUTION: Beware of falling wise. pipe when cutting long lengths. Do not Damage blade or cut line indicator when positioning workpiece in vise.
180°. Place machine into case. TC 4.5 MAINTENANCE SECTION VI The TC 4.5 has been designed to minimize maintenance. Clean and inspect moving parts regularly for wear. Check power cord peri- odically for damage or wear. Replace if cracked or damaged.
TUBE CUT OFF SAW TC 4.5 TC 4.5 OPERATIONAL CHARTS & GRAPHS SECTION VII Speed Selection Information: Description Wall Thickness Motor Speed Speed Dial All Stainless Steel 300 Series .030” to .080” High “G” All Stainless Steel 300 Series .080” to .120”...
TUBE CUT OFF SAW TC 4.5 TC 4.5 TROUBLE SHOOTING SECTION VIII Trouble Possible Cause Remedy Motor Will Not Run ......Power Unit Not Connected ......Check Power Cord & Connection Motor Runs Slowly ......Improper Speed or Gear Box Setting ..... Refer to Speed Control & Gear Box Info.
TUBE CUT OFF SAW TC 4.5 SECTION IX PARTS LISTS & EXPLODED VIEW DRAWINGS...
Seite 16
TUBE CUT OFF SAW TC 4.5 TC 4.5 Bill of Material Part # 20-000-01 & 20-000-02 Ref. # Part # Qty. Description Ref. # Part # Qty. Description 19-015-00 Bearing, Drawn Cup Needle 20-001-00 Frame, Main 20-034-00 Bearing, Thrust 20-002-00...
TUBE CUT OFF SAW TC 4.5 TC 4.5 ORDERING INFORMATION SECTION X To place an order or to get more detailed information on any E.H. Wachs products, call us at: 1-800-323-8185. ORDERING REPLACEMENT PARTS Please use parts list provided in manual. Have part description and part number of required replacement part or parts to help expedite order and insure proper parts are being ordered.