Werbung
Verfügbare Sprachen
Verfügbare Sprachen
zone, there is a delaytime of 9 sec. in which no
motion is detected.
à Pulse operation, chime function
Key
, acknowledgement!
Perform movement test. Light goes on for 1 sec.
and off for 9 sec. A movement can only turn on
the light again after this 9 sec. has elapsed.
à Turn off LED: Key
The LED no longer reacts to movement.
à Switch off PIR: Key
The 360° creep-under protection no longer reacts.
In order to ensure that this function is deactivated,
cover the 4 frontal planes with the clips. For faster
results, simply stick with insulating tape.
à Set test operation: Key
Perform movement test. The LUXOMAT
on the light for 1 sec. and then does not react for
2 sec. Next movement test, 1 sec. light on, 2 sec.
light off, etc.
à Set party function: Key
The constant light is turned on regardless of the
setting of the light sensor and regardless of whether
movement was detected. The light can be switched
off by pressing
light turns off automatically after a period of 12
hours.
à The
key turns the light off again. There is than
a 9 sec. period before activation.
Example 2:
Setting a time and light sensor value,
(LUXOMAT
RC-plus "opened"
®
Putting into operation, see example 1,
à Wait 1 min. self test time, "open" RC-plus, key
à Set time to 12 min.: Key
Check whether constant light is turned on via the
movement test. Should there be no reaction
à Read in current light value. Key
acknowledgement!
A movement now causes the light to turn on.
Light value max. 2500 lux, limited internally!
à Enter light sensor value: Experience has shown
that the unit is usually installed and the work
completed during daylight hours with the result
that it is difficult to preset a suitable value in the
traditional manner using the adjustable knob.
E.g. selection of one of the 4 fixed light sensor
values, set 25 lux: Key
The LUXOMAT
RC-plus will now switch on in
®
advanced dusk.
, acknowledgement!
LED
, acknowledgement!
PIR
, acknowledgement!
TE ST
®
, acknowledgement!
If this button is not pressed, the
)
, acknowledgement!
12
min
,
, acknowledgement!
à Lock LUXOMAT
ment!
Should the light sensor value set not suit the
customer this can be changed as follows:
à Open LUXOMAT
acknowledgement!
à Read in current light sensor value, key
acknowledgement!
à Lock LUXOMAT
acknowledgement
This individually sets the dusk value which the
LUXOMAT
customer's wishes.
Example 3:
switches
LUXOMAT
®
Only the test and constant light functions can be
switched on in the "locked" state.
à Turn on test operation: key
ment!
Regardless of the preset light sensor value, every
movement triggers a reaction.
à Leave test operation: key
The previously set time and light sensor values
apply (see also
à Setting the party function
Constant light is on; can be switched off again
as required at any time using the light off key
Press
Example 4:
Adjustment of 16 min./25 lux and additional
Vacation/Comfort- and Party function
Putting into operation, see example 1
à Wait 1 min. self test time, "unlock" with key
(àoptional RESET : key
à Enter 16 min. time: key
à Enter 25 lux: key
à Enter Alarm:, key
à Enter Vacation/Comfort: key
ment!
à Lock LUXOMAT
ment!
à Enter Party program: key
Light ON!
31
RC-plus, key
®
RC-plus, key
®
RC-plus, key
®
is to turn on in accordance with the
®
RC-plus "locked"
TE ST
, acknowledgement!
RESET
)
RESET
, acknowledgement!
key for light off.
, acknowledgement!)
RESET
, acknowledgement!
16
min
, acknowledgement!
, acknowledgement!
Alarm
RC-plus, key
®
, acknowlegement,
, acknowledge-
,
,
,
, acknowledge-
Co
, acknowledge-
, akcnowledge-
Werbung
