KEE ACTION SPORTS nuke bunker Benutzerhandbuch

AGES 9+
WARNING: This is not a toy. Not to be used by
persons under the age of 9. Misuse can cause serious
injury. Full eye protection speci cally designed for JT
Splatmaster or paintball must be worn by the user
and any person within range; full face protection User's Manual
required for player vs. player play any person within
range. Adult (age 18+) supervision is required.
Product is for outdoor use. Always put "safety on"
when not in use. Read all instructions prior to using.
WARNING!
Eye protection designed specifically
for JT Splatmaster or paintball must be worn by the user and
persons within range. Safety is no accident.
WARNING!
• Read Operator's Manual Before Using
• Use Only as Directed
• Keep away from sharp, hot or dangerous objects
• This Item in NOT to be Used as a Pool Toy or Lifesaving Device
• This Recreational Inflatable Bunker is NOT for Use on Commercial
Paintball Fields
• Any Commercial Use of this Product will Void all Manufacturer's
Warranties
• Only For Use with JT SplatMaster products
DO NOT OVER INFLATE!!!
JT SplatMaster 11723 Lime Kiln Rd. Neosho, MO
www.JTSplatMaster.com 64850 800-220-3222
MADE IN CHINA
INFLATION
1. Locate the Fill/Release Valve on the lower side of the
bunker (Fig. 1).
2. The Fill/Release Valve is pressed into the air chamber to prevent
breakage, pull the entire valve free from the bunker.
(Fig.1)
3. The Fill/Release Valve can be inflated in two ways:
Pulling off the outer plug gives access to the Pump Valve
A
(Fig. 2). This valve is designed for use with aftermarket inflation
pumps (not included). Use only suitable pumps and/or nozzles
as the valve could otherwise be damaged.
(Fig.2)
Pulling the Pump Valve off allows an open hole for you to
B
inflate the bunker by any other means (Fig. 3). A leaf blower
or shop-vac in reverse work well as secondary options to
a specific inflation pump. (Adult usage only) Do not use
compressed air and do not inflate by mouth. Never place
any valve in the mouth.
(Fig.3)
4. DO NOT OVER INFLATE!
5. Bunkers work best when slightly under-inflated or soft.
6. Once filled as desired, close the Fill/Release Valve quickly to
prevent air escaping.
7. Press the entire Fill/Release Valve into the bunker so it no longer
protrudes.
NOTE: The heat of the sun can increase the air pressure. If this should
happen, let some air out through the valve to reduce the pressure.
DEFLATION
To deflate the bunker, open both the outer plug and the Pump
Valve plug (Fig. 3).
WATER STABILIZATION CHAMBER
The JT SplatMaster Nuke Bunker has a water stabilization chamber
to prevent the bunker form falling over. A standard garden hose
can be used to fill the chamber by following these steps:
1. Locate the Water Chamber Plug on the bottom of the bunker
(Fig. 4).
2. Open the Water Chamber Plug and make sure the Air Hole is
closed.
3. Insert a garden hose into the Water Hole.
4. Holding the hose securely into the Water Hole, turn on the faucet
and allow water to slowly fill the chamber.
5. The Water Chamber Plug has a valve flap that will open when
water flows through the hose.
6. Allows the chamber to fill completely, turn off the water and then
close the plug.
7. Place the bunker upright in a suitable location, making sure the
space is free from stones or sharp objects.
To empty the chamber, open the Water Chamber Plug and the Air Hole Plug.
To increase the water flow, hold the valve flap open.
(Fig.4)
AIR HOLE
WATER CHAMBER PLUG
TARGET INSTALLATION
The Nuke Bunker comes with a target that attaches with Velcro™.
Align the Velcro™ patches on the back of the target to those on the
side of the bunker and press firmly. The target can be peeled off
the bunker for cleaning and storage.
REPAIRING ACCIDENTAL DAMAGE
To repair any accidental puncture, use the included patch kit
and follow these steps:
1. Clean the area around the leak with soap and water
2. Let the area dry completely for about 10 minutes
3. Cut a patch from the extra material (included), about twice the
size as the hole
4. Remove the paper backing from the patch
5. Apply the patch over the hole, forcing any bubbles out from
under the patch
6. Hold firmly in place for 30 seconds
7. Allow the patch to cure for about 1 hour before using bunker
CLEAN UP AND STORAGE
Bunkers can be cleaned with mild soap and water and should be
rinsed off and cleaned after every use. Completely empty the water
chamber and air chamber prior to storage. Once the air and water
is out, leave the valve open and roll the bunker up for storage. If
available, use a shop-vac to completely deflate the bunker.
WARNING!
PAINTBALL GUNS AND PAINTBALL
GUN ACCESSORIES ARE NOT TOYS!
- Careless use or misuse may result in serious bodily injury or death!
- Full eye protection specifically designed for JT Splatmaster or
paintball must be worn by the user and any person within range;
full face protection required for player vs player play and any
person within range.
- Must be 9 years of age or older to operate or handle any JT
Splatmaster gun and JT Splatmaster gun accessories. Children
under the age of 18 require adult or parental supervision.
- Read and understand all cautions, warnings, and operating manuals
before using any paintball gun or paintball gun accessory.
- Do not aim paintball gun at eyes or head of people or at animals.
- Paintball guns are to be used with Paintballs only.
- Use common sense and have fun.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE,
OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
PRODUCT OR THE USE OF ANY PRODUCT.
WARNING:
This product contains one or more chemicals that
are known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
JT SplatMaster is a brand of KEE Action Sports, LLC. Design rights & all rights
reserved. All patterns, drawings, photographs, instructions or manuals remain
the intellectual property of the manufacturer. All rights will be strictly enforced.
ASTM International, formerly known as the American Society
for Testing and Materials (ASTM), is a globally recognized
leader in the development and delivery of international voluntary
consensus standards used around the world to improve product
quality, enhance safety, facilitate market access and trade, and
build consumer confidence. ASTM International, 100 Barr Harbor
Drive, PO Box C700, West Conshohocken, PA, 19428-2959
USA, www.astm.org