Noise And Vibration; Warranty - Felisatti R400 Bedienungsanleitung

- Insert the cutter between the gripper jaws.
- Tighten the ring nut, making sure that the cutter is
fitted securely to the gripper..
REMOVING THE CUTTER
- Loosen the lock nut until the cutter is released.
- Remove the cutter from the gripper.
If the cutter diameter is not to be changed, leave the
lock nut on the shaftAtención:
ATTENTION! Carefully follow the instructions given
for fitting and removing cutters, if not the gripper
and cutter may be locked onto the gripper shaft.

NOISE AND VIBRATION

This tool has been designed and made to reduce noise
to a minimum. However, in spite of this, in certain
circumstances the maximum noise level in the
place of work could exceed 85 dBA. In this case,
the operator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN60745-1, usually reach:
Acoustic pressure = 80 dB(A)
Sound-power level = 93 dB(A)
Use ear protection!
Vibration acceleration = 3,3 m/s2
MAINTENANCE AND CARE
WARNING! Always unplug the machine before
carrying out work on it.
Warning! Type Y attachment. If the supply cord is
damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to
avoid a hazard.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly
tightened.
Should any screw be loose, tighten it immediately.
Failure to do so could put you at serious risk.
- Motor maintenance: Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast
the motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
- Brush replacement: The brushes should be
replaced after 150 - 200 hours use or when they are
less than 10 mm long. Have this done by an Official
Service Centre. We recommend that at every second
change of brushes, you take the machine to one of our
Official Service Centres for general cleaning and oiling.
- Use only Felisatti accessories and spares parts the
changing of which is not covered in this instruction
manual, should be replaced in a Felisatti Official
Service Centre.
¡ Do not dispose of electric tools
inthe household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.

WARRANTY

See general warranty conditions printed on the at-
tached sheet.
DECLARATION OF CONFORMITY
Business name of the manufacturer:
INTERSKOL POWER TOOLS S.L.
Full address of the manufacturer:
Crta. de Sant Joan de les Abadesses, s/n
17500 RIPOLL-(Girona) SPAIN
Name and
(established
compiled the technical file:
Jordi Carbonell and Santiago López
Ctra. de Sant Joan de les Abadesses, s/n
17500
RIPOLL-(Girona) SPAIN
Product name: Router
Commercial name: Router
Model: R400
Type: Electric power tools
Serial Number: see label of the tool
Fulfils all
Directives
2004/108/EC, 2002/96/EC, 2002/95/EC,
2009/251/EC We hereby declare, under
our sole responsibility, that the FELISATTI
brand products described in this manual
R400 comply with the following standards
or standard
EN60745-2-3,
EN61000-3-2, EN61000-3-3.
14
Jordi Carbonell
Plant Mgr
We reserve the right to make technical changes 10/2014
address of the
in the Community)
the relevant provisions
2006//95/EC, 2006/42/EC,
documents: EN60745-1,
EN55014-1, EN55014-2,
Santiago López
Marketing Mgr
person
who
of