Safety Instructions - Felisatti R400 Bedienungsanleitung

Translation of the original instructions
TECHNICAL SPECIFICATIONS
ROUTER TRIMMER
Absorbed power
Speed unload (r.p.m.)
Speed full load (r.p.m.)
Gripper capacity
Mill travel
Weight
IDENTIFICATION
A. Logotype plate
B. Data plate
C. Principal handle
D. Switch
E. Switch push-button
F. Auxiliary handle
G. Clamping bit plier
H. Base
I. Conveyor glow screen
DOTACION STANDARD
- 6 diameter grippers
- Clamping ring nut,
- Suction hood
- Pantograph kit
- Service spanners
- Warranty
- Operating instructions

SAFETY INSTRUCTIONS

• See "Safety Instructions" manual, supplied with this
instruction manual.
• WARNING! Material containing asbestos must not be
polished. Working
amianthus/asbestos and/or silica stones produces a
dust, which is harmful to health. Protect yourself from
inhaling this dust, in compliance with current
regulations on accident prevention.
• For your personal safety, always connect the
machine to a mains supply protected by a differential
and thermal cutout switch, in accordance with
regulations on low-voltage wiring sitemaps.
• Do not pierce the motor housing as this could
damage the double insulation (use adhesive labels).
• Check the work area with a metal detector for hidden
wires, gas and/or water pipes.
• Always unplug the machine before carrying out
work on it.
• Always stop the machine by switching it off, not by
unplugging it.
• WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by
an official service centre.
• Always keep the mains lead clear of the working
range of the machine.
• Only plug the machine in when it is switched off.
• Do not allow the machine to get wet, nor should it be
used in wet environments.
W
r.p.m.
r.p.m.
mm
kg
with materials containing
• When using the machine, always wear safety
goggles, gloves and non-slip footwear, and it is
advisable to wear ear protection.
• Check for correct piece fixing before commencing
any operation.
• Only milling heads with acceptable revolutions that
are at least the same as the maximum off-load
revolutions of the machine should be used.
• The milling head shaft diameter should match the
inside diameter of the tool-holder (locking clip).
• It should be ensured that the milling head is firmly
held in place before the machine is operated.
• The clip-carrier shaft support lever must only be
operated when the machine is stopped.
• The milling head should only be brought into contact
with the work-piece after it has been switched on.
• The machine must be firmly held by the grips. Other-
wise the recoil produced could cause the machine to
work imprecisely or even dangerously.
• Hold the machine firmly in both hands and in a stable
position.
• During use, it should be ensured that the milling head
is in the centre of the copy bushing in order to
prevent any personal injury or damages to the work-
piece.
• The milling machine must never be used on metal
objects, such as nails and screws.
• Hand must be kept clear of the milling machine while
it is operating.
• The cutting depth must never be adjusted with the
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
work-piece.
• The operator should remain alert and keep the milling
head apart from all objects during operation.
• When the milling operation has been completed,
locking lever should be operated so that the machine
returns to its upper starting position.
• The motor must be allowed to come to completely
stop before being put to one side between uses.
• The milling heads should be protected from impacts
and knocks.
• The milling heads should not be touched after use
because they could cause serious burns.
.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is
correct: it must be the same as that on the specification
label.
R400
450
24000
13000
6-6.35-8
40
1,7