Troubleshooting - Philips NT9110 Bedienungsanleitung

ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips! To
fully benefit from the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
Cutting element
A
Trimming head
B
^= 'Open' indication
C
Setting indicator
D
Battery compartment cover
E
Motor unit
F
0 = 'Off ' indication
G
I = 'On' indication
H
Sealing ring
I
Protection cap
J
Short eyebrow comb (3mm/0.12in)
K
Long eyebrow comb (5mm/0.2in)
L
Brush
M
Important
Read this user manual carefully before you use the appliance
and save it for future reference.
Warning
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
- Children should be supervised to ensure that they do
not play with the appliance.
Caution
- This appliance can only be operated on a battery.
- Do not use the appliance when the cutting element or
the appliance itself is damaged or broken, as this may
cause injury.
- Use and store the appliance at a temperature between
15°C and 35°C.
- This appliance is only intended for trimming nose hair,
ear hair, eyebrows and neck hair. Do not use it for
another purpose.
- Remove the battery from the appliance if you are not
going to use it for some time.
- If the appliance is subjected to a major change in
temperature, pressure or humidity, let the appliance
acclimatise for 30 minutes before you use it.
- For hygienic reasons, the appliance should only be used
by one person.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding
electromagnetic fields (EMF). If handled properly
and according to the instructions in this user manual, the
appliance is safe to use based on scientific evidence available
today.
Preparing for use
1 To remove the battery compartment cover, turn it to
the left until the setting indicator points to the 'open'
( ^) indication. Then pull the battery compartment
cover off the motor unit. (Fig. 2)
2 Put the battery in the battery compartment (Fig. 3).
Make sure the + and - poles of the battery point in the right
direction.
Note: The appliance runs on one R6 AA 1.5-volt battery
(included). Preferably use Philips alkaline batteries. A new AA
alkaline battery has an operating time of up to 2 hours.
3 Slide the battery compartment cover back onto the
motor unit. Turn the cover to the right until the setting
indicator points to the 'off' (0) indication (Fig. 4).
Make sure the sealing ring is properly placed (Fig. 5).
,
To avoid damage due to battery leakage:
- do not expose the appliance to direct sunlight.
- do not expose the appliance to temperatures higher
than 35°C.
- remove the battery if you are not going to use the
appliance for a month or more.
- do not leave an empty battery in the appliance.
Using the appliance
1 Remove the protection cap by pulling it off the
appliance (Fig. 6).
4203.000.5813.4
2 To switch on the appliance, turn the battery
compartment cover to the right until the setting
indicator points to the 'I' indication (Fig. 7).
3 Before you use the trimmer for the first time, test it
on a small part of your arm or leg.
If any irritation or allergic reaction occurs, discontinue
use immediately. Do no use the trimmer on sensitive or
irritated skin.
4 Trim your nose hair, ear hair, neck hair or eyebrows as
described in the rest of this chapter.
5 To switch off the appliance, turn the battery
compartment cover to the left until the setting
indicator points to the '0' indication (Fig. 8).
6 Put the protection cap back onto the cutting element
after use to prevent damage.
Trimming nose hair
Make sure your nostrils are clean.
1 Carefully insert the cutting element into one of your
nostrils.
Do not insert the cutting element more than 0.5cm into
your nostrils.
2 Slowly move the appliance around to remove all
unwanted hairs in your nostrils (Fig. 9).
Trimming ear hair
Make sure your outer ear channels are clean and free from
wax.
1 Slowly move the cutting element along the rim of
the ear to remove hairs that stick out beyond the
rim (Fig. 10).
2 Insert the cutting element into the outer ear channel.
Do not insert the cutting element more than 0.5cm into
your ear channel, as this could damage the eardrum.
3 Slowly turn the appliance around to remove all
unwanted hairs from your outer ear channel (Fig. 11).
Trimming neck hair
1 Place the cutting element gently on the skin and move
the appliance slowly over the skin against the direction
of hair growth. (Fig. 12)
Trimming eyebrows
With the short and long eyebrow combs, you can use the
appliance to trim your eyebrows to a uniform hair length.
1 Comb your eyebrows in the direction of hair
growth (Fig. 13).
2 Choose the short or long comb, depending on the
desired hair length. The indications 'short' and 'long'
are on the combs.
- short comb: 3mm/0.12in
- long: 5mm/0.2in
Tip: We advise you to start trimming with the long comb. If you
think your eyebrows are still too long after this, use the short
comb.
3 Slide the eyebrow comb onto the cutting element.
Make sure that the eyebrow comb has been properly slid
into the grooves on both sides (Fig. 14).
4 To switch on the appliance, turn the battery
compartment cover to the right until the setting
indicator points to the 'I' indication (Fig. 7).
5 Move the comb over the eyebrow from the outer tip
of the eyebrow towards the base of the nose (against
the direction of hair growth) (Fig. 15).
Never try to trim your eyelashes. Keep the appliance away
from your eyes.
Cleaning
Clean the appliance immediately after use and when a lot of
hair or dirt has accumulated on the cutting unit.
Never use compressed air, scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol or acetone to
clean the appliance.
The trimming head cannot be opened or detached.
1 Make sure the appliance is switched off.
2 Clean the cutting element with the brush supplied.
Pay extra attention to the edges of the cutting
element (Fig. 16).
Tip: To remove all hairs, let the appliance run briefly and then
clean the cutting element with the brush again.
3 Clean the combs under the tap.
4 Switch on the appliance.
5 Rinse the cutting element under the tap with hot
water (Fig. 17).
6 Switch off the appliance and let it dry.
Do not tap on the cutting element.
Do not use any sharp objects to clean the cutting element.
Note: The appliance does not need any lubrication.
Replacement
If the eyebrow combs are damaged or worn, always replace
them with original Philips eyebrow combs, which are available
from authorised Philips service centres.
The cutting element cannot be replaced. If the cutting
element is damaged or worn, you must discard the whole
appliance (see chapter 'Environment') and replace it with a
new one.
Environment
- Batteries contain substances that may pollute the
environment. Remove the battery when it is empty or
when you discard the appliance. Do not throw away the
battery with the normal household waste, but hand it in
at an official collection point (Fig. 18).
- Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in at
an official collection point for recycling. By doing this,
you help to preserve the environment (Fig. 19).
Guarantee and service
If you need service or information or if you have a problem,
please visit the Philips website at
www.philips.com or contact the Philips Consumer Care
Centre in your country (you find its phone number in the
worldwide guarantee leaflet). If there is no Consumer Care
Centre in your country, go to your local Philips dealer.
Guarantee restrictions
The guarantee becomes invalid when the appliance is not
used and/or not maintained properly or when it is damaged
by dropping.

Troubleshooting

This chapter summarises the most common problems you
could encounter with the appliance. If you are unable to
solve the problem with the information below, contact the
Consumer Care Centre in your country.
Problem Possible cause Solution
The The cutting Soak the
appliance element is cutting element of
becomes dirty. the nose trimmer in
hot during a bowl with water
use. and some washing-up
liquid for 2 minutes.
Then rinse the cutting
element with fresh
water and let it dry.
Clean the cutting
element after every
trimming session.
The The battery is Replace the battery
appliance empty. by a new one (see
does not chapter 'Preparing for
work. use').
The cutting Soak the
element is cutting element of
dirty. the nose trimmer in
a bowl with water
and some washing-
up liquid soap for 2
minutes. Then rinse
the cutting element
with fresh water
and let it dry. Clean
the cutting element
after every trimming
session.
2/13