Gemini mm-04 Bedienungshandbuch Seite 4

INTRODUCTION:
Congratulations on purchasing a Gemini MM-04 4U 19", 4
channel, rack mounted audio EFX mixer. This state of the art
mixer is backed by a 3 year warranty, excluding crossfader. The
crossfader is backed by a separate 90 day warranty. Prior to use
we suggest that you carefully read all the instructions.
FEATURES:
- 4U 19" rack mounted audio EFX mixer
- 4 stereo channels
- 6 line, 3 mic, 2 convertible phono/line RCA inputs
- Master, zone & record RCA outputs
- Balanced master output
FACE:
- 3 band rotary line EQ control per channel with cut feature
- Bright blue LCD display
- 26 DSP effects module with a wide range of parameters
- Dry/Wet fader control
- Rotary control EFX selector
- Rotary parameter control
- Large backlit soft touch on/off EFX button
- Fully removable, user replaceable Rail Glide cross fader
- Assignable cross fader
- Rotary gain control per channel
- Dual VU display with bright LED
- Push-button cue section with cue/PGM fader control
- Rotary master, zone, balance and cue volume controls
- XLR-1/4" combo mic input & 2 x 1/4" Mic inputs
- 2 band rotary mic EQ controls
- Rotary mic volume control
- Auto talk-over feature
- Face plate located 1/4" headphone jack
PRECAUTIONS:
1. All operating instructions should be read before using this
equipment.
2. To reduce the risk of electrical shock, do not open the unit.
Please refer servicing to a Gemini qualified service technician.
IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS
UNIT CALL GEMINI CUSTOMER SERVICE AT: 1 (732) 738-9003. DO
NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER.
3. Do not expose this unit to direct sunlight or to a heat source
such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid sol-
vents or other cleaning detergents.
5. When moving this equipment, it should be placed in its origi-
nal carton and packaging. This will reduce the risk of damage
during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON
ANY CONTROLS OR SWITCHES.
CONNECTIONS:
1. Before plugging this unit into any outlet, make sure that the
VOLTAGE SELECTION SWITCH (1) is set to the proper volt-
age. To change the selection, unscrew the hard plastic protec-
tive top with a Phillips head screw driver. Then use a flat head
screw driver to move the switch to the proper selection
(115V/230V).
2. Located on the rear panel is the POWER CORD (2). Before
plugging the POWER CORD (2) into a power outlet, make sure
the POWER SWITCH (64) located on the face panel is turned
off.
NOTE: LOCATED BY THE POWER CORD (2) JACK IS A 250V FUSE (67) TO
PROTECT AGAINST ELECTRICAL SURGES. TO REPLACE THE FUSE,
PLACE A FLAT HEAD SCREWDRIVER INTO THE GROOVE LOCATED INSIDE
THE POWER CORD JACK (2) AND POP THE FUSE OUT. REPLACE THE FUSE
WITH ONLY A 250V FUSE.
3. The MM-04 has 4 sets of outputs:
- The MASTER OUTPUT (4) jacks also connect to the main
amplifier with RCA cables.
- The BALANCED MASTER OUTPUT (3) jacks connect the
mixer to main amplifier using standard cables with 1/4" TRS
connectors. We recommend using balanced cables if the dis-
tance to your amp is 10 feet or more.
- The REC OUTPUT (5) jacks can be used to connect the mixer
to the record input of your recording unit, thus enabling you to
record your mix by connecting these units with RCA cables.
- The ZONE OUTPUT (6) jacks allow the connection of an addi-
tional amplifier with RCA cables.
4. Located on the rear panel are 2 PHONO(PH)/LINE(LN) con-
vertible RCA inputs (13, 10), and 4 LN RCA inputs (16, 14, 11,
7). The CONVERTIBLE RCA INPUTS (13, 10) for CHANNEL
(CH) 2 (35) & CH 3 (42) allow PH and LN level equipment to be
connected to the mixer. To adjust the CONVERTER
SWITCH(es) (9, 12), just flip the switch up to operate PH 1 or
PH 2. Flip the switch down to operate through LN 2 or LN 4. The
PHONO INPUTS (10,13) only accept turntables with a magnet-
ic cartridge. When using (a) turntable(s), you will need to ground
the RCA cable(s) by screwing in the grounding fork(s) to the
GROUNDING SCREW (65) located in the rear panel of the MM-
04 mixer. This is located in between the CONVERTER
SWITCHES (9, 12). The stereo LN INPUTS only accept line
level inputs such as a CD, DAT, MiniDisc, etc.
NOTE: WHEN USING A TURNTABLE, NOT ATTACHING A GROUND MAY
CAUSE A SYSTEM "HUM."
5. Headphones may be plugged into the face-plate located 1/4"
HEADPHONE JACK (58).
6. The MIC 1 (17) input (located on the face panel) is a combi-
nation XLR & ¼" connector. The MIC 2 (15) & MIC 3 (8) inputs
(in the rear panel) accept only 1/4" connectors. The MIC inputs
accept balanced and unbalanced connections.
OPERATING INSTRUCTIONS:
1. Once all of your connections have been made in the rear
panel, turn on the mixer by pressing the POWER SWITCH (64).
2. CH 1: To bring this channel into PROGRAM (PGM), you must
first decide which line will be in use. Use the LN SWITCH (22)
to toggle from LN 1 (16) to MIC 2 (15) on this channel. Slowly
raise the CH 1 FADER CONTROL (28) to a comfortable level,
once you've selected the proper line. You can further modify the
sound output of this channel by adjusting the rotary GAIN (23),
HIGH (25), MID (26), LOW (27) controls located to the left of the
CH 1 FADER CONTROL (28).
3. CH 2: To bring this channel into PGM, you must first decide
which line will be in use. Use the LN SWITCH (29) to toggle from
PH 1/LN 2 (13) to LN 3 (14) on this channel. Slowly raise the CH
2 FADER CONTROL (35) to a comfortable level, once you've
selected the proper line. You can further modify the sound out-
put of this channel by adjusting the rotary GAIN (30), HIGH (32),
MID (33), LOW (34) controls located to the left of the CH 2
FADER CONTROL (35).
4. CH 3: To bring this channel into PGM, you must first decide
which line will be in use. Use the LN SWITCH (36) to toggle from
PH 2/LN 4 (10) to LN 5 (11) on this channel. Slowly raise the CH
3 FADER CONTROL (42) to a comfortable level, once you've
selected the proper line. You can further modify the sound out-
put of this channel by adjusting the rotary GAIN (37), HIGH (39),
MID (40), LOW (41) controls located to the left of the CH 3
FADER CONTROL (42).
5. CH 4: To bring this channel into PGM, you must first decide
which line will be in use. Use the LN SWITCH (43) to toggle from
LN 6 (7) to MIC 3 (8) on this channel. Slowly raise the CH 4
FADER CONTROL (49) to a comfortable level, once you've
selected the proper line. You can further modify the sound out-
put of this channel by adjusting the rotary GAIN (44), HIGH (46),
(4 4 )