PEUGEOT EnergySaw-254R Bedienungsanleitung Seite 26

SAFETY INSTRUCTIONS SPECIFIC TO MITRE SAWS
1. This saw is designed for cutting only wood, non-ferrous metals and plastic.
2. Never use blades other than those recommended in this instruction manual.
3. Do not use high-speed steel (HSS) blades, or damaged or warped blades.
4. Do not use the saw without first putting the guards in place and securing them correctly.
5. Replace the table insert when it is worn.
6. Use only the saw blades recommended by the manufacturer and compliant with standard EN847-1.
7. Connect your mitre saw to a dust collecting device (diameter Ø 32 mm) while sawing.
8. Select saw blades that are appropriate for the material to be cut.
9. Check the maximum cutting depth.
10. While sawing long pieces, always use side extensions and clamps or other securing devices to hold the workpiece
adequately.
11. Wear appropriate personal protective equipment if needed, including:
- ear protection to reduce the risk of damaging your hearing;
- safety goggles;
- breathing mask to reduce the risk of inhaling dust particles, which are harmful to health;
- safety gloves while handling saw blades and sharp unworked materials.
12. The operator must be correctly trained in the use, adjustment and operation of the machine.
13. Provide sufficient lighting in the work area and its immediate surroundings.
14. If the saw is fitted with a laser, do not use any other type of laser. Repairs may only be carried out by the laser manu-
facturer or by an approved representative.
15. Do not attempt to remove offcuts or other parts of the workpiece from the sawing area while the machine is opera-
ting if the saw head is not in the home position.
16. Never use a mitre saw in the presence of flammable gas, fumes or liquids.
17. Remove any nails from the workpiece in order to avoid sparks, which could lead to fires.
18. To avoid fires or toxic reactions, never use petrol, acetone or any other similar solvent to clean the saw.
19. Set the saw on the table using appropriate pads to reduce the noise and vibrations from the machine.
20. Always carry the saw by its carry handle.
WARNING!
• Make sure that the arm is correctly locked while making mitre cuts.
• Keep the working area clean and free of debris or cutting scrap around the machine. Use blades that are properly shar-
pened. Check the maximum speed stated on the blade.
• When replacing the laser, make sure not to use a different type of laser. Repairs may only be made by the laser manu-
facturer or another authorised party.
• Do not remove debris or scrap from the cutting area while the machine is operating and when the saw head is down.
• Make sure that the machine is always secured to a bench or a supporting surface whenever possible.
Motor:
Speed:
Blade dimensions:
Table dimensions:
Table height:
Machine dimensions:
Weight:
Mitre stop, left and right:
Angle stop:
Mitre saw:
90° x 90°:
90° x 45°:
45° x 90°:
45° x 45° :
Circular table saw:
Max. cutting height at 90°:
Max. cutting height at 45°:
SPECIFIC INSTRUCTIONS TO MITRE SAW
TECHNICAL SPECIFICATIONS OF THE MACHINE
1800w - 230v AC 50 Hz
4200 revolutions/min.
254 x 30 x 2.8 mm
510 x 470 mm
820 mm
800 x 720 x 1270 mm
32 kg / 35 kg
0° - 15° - 22.5 ° - 31,6° - 45°
0 and 45°
60 x 155 mm
60 x 105 mm
40 x 155 mm
40 x 105 mm
70 mm
50 mm
symbols
V...........................................Volts
A.......................................... Amperes
Hz........................................ Hertz
W.........................................Watts
Min..................................... Minutes
~......................................... Alternating current
h......................................... Hours
min-1..................................Revolutions per minute
I.......................................... ON
0........................................ OFF
wear safety goggles
wear ear protection
wear a breathing mask
26