Steinbach Speed Clean Classic 300 Bedienungsanleitung Seite 11

Cirkulation Function: circulate water after chemical treatment.
This position is used during certain pool cleanups and
chemical treatments when you don't want the water
contaminating the sand. In this position, water is only
directed through the valve back to the pool and does
not filter through the sand.
Backwash Function: clean filter of captured debris. This is the
position needed to clean the filter/the sand. You'll know
it is time to backwash when the pressure gauge rises
0,3 to 0,6 bar above what it normally reads when the
filter is clean.
In this position, the water is fed in at the bottom soil
filter and it then runs upwards through the sand. The
collected dirt is loosened, sucked up and flows through
the dirt pipe out of the filter.
Closed Function: Cleaning the hair and lint strainer. This posi-
tion stops the flow of water into the pump and filter.
CAUTION: Do not run pump with valve in this position.
Purge/ Function: bypass the filter. This position is ideal for
Drain vacuuming pools with large amounts of debris or after
an algae treatment. In this position, water bypasses
the filter and sends all the water and contaminates out
the waste line.
Winterize Function: winterizing and storage. In this position,
the valve lever is between positions which removes
pressure from internal valve components for winter
(off-season) storage.
CAUTION: Do not run pump with valve in this position.
Filtering time
The swimming pool's water should be circulated and filtered at least 3
to 5 times in a 24 hour period, depending on the load and the size of the
filter system. The time required is based on the performance of the filter
system and the size of the swimming pool. However, we recommend a
minimum running time of 12 hours per day.
Power source Instructions
The filter system you have purchased is equipped with a connection
cable, which may only be connected to a circuit with a residual current
circuit breaker (RCCB) with a rated residual current of no more than
30mA.
Technical data:
040300 Classic 300
■ Circulation power 3,800 l/h
■ Pump is not self-priming
■ maximum water temperature 35 °C
■ 230 V / 200 W
■ 7 way valve with pressure gauge
■ Tank Ø 320 mm
■ Connector Ø 32/38 mm
■ Ground plate
■ requires approx. 20 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 19,000 l capacity
■ Available separately: Speedpart container for UV System Speed UV
040310 Classic 310
■ Circulation power 4,500 l/h
■ self-priming pump with pre-filter
■ maximum water temperature 35 °C
■ 230 V / 250 W
■ 7 way valve with pressure gauge
■ Tank Ø 320 mm
■ Connector Ø 32/38 mm
300/310/400_040300/040310/040340_v1901
■ Ground plate
■ requires approx. 20 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 22,000 l capacity
■ Available separately: Speedpart container for UV System Speed UV
040340 Classic 400
■ Circulation power 6,600 l/h
■ self-priming pump with pre-filter
■ maximum water temperature 35 °C
■ 230 V / 450 W
■ 7 way valve with pressure gauge
■ Tank Ø 370 mm
■ Connector Ø 32/38 mm
■ Ground plate
■ requires approx. 25 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 33,000 l capacity
■ Available separately: Speedpart container for UV System Speed UV
Operation with a pool vacuum cleaner
(Illustration 8)
■ The pool vacuum cleaner's hose can be connected directly to the filter
system's suction pipe. In doing so, the pool vacuum cleaner's hose
must be completely filled with water.
■ The use of a skimmer with a strainer basket is recommended for filter
systems without pre-filters.
■ Please observe the pool vacuum cleaner's operating instructions. To
prevent the filter from running dry and thus overheating, no air should
be allowed to enter the filter system.
■ Please select the "FILTERN" position on the valve head.
■ Alternatively, you can also select the "ENTLEEREN (empty)" position,
for example if algae forms in the pool. Dirty pool water will not then run
back into the pool, but will be directly channelled away via the waste pipe.
When selecting this setting, it is necessary to re-fill your pool to the
correct level after cleaning, if necessary.
Problem treatment
Cause of Problems
Sand contaminated with dirt
Pump sucks air
(Bubbles at the inlet)
Skimmer or pump gets too little
water
Skimmer basket contaminated
Prefilter basket of the filter pump
contaminated
For any errors not listed above, please contact your dealer!
Important Note
To winterize the system
■ Unplug the pump from the power source.
■ Close the shut off valves or block the flow of water at the pool inlet
and return ports.
■ Disconnect the filtration system from the pool, drain the tank and
hoses.
■ Place the handle on the central valve in position 'Winterize' to relieve
Solution
Backwashing (cleaning of the
sand)
defective hoses,
tighten hose clamps
Check water level and increase
if necessary, check the intake for
dirt accumulation
Cleaning of the skimmer basket
Cleaning of the prefilter basket
EN
11