Instructions And Security; Safety Instructions - Valpes VRX25 Bedienungsanleitung

INSTRUCTIONS AND SECURITY

DESCRIPTION
VALPES electric actuators have been designed to perform the control of a valve with 90° rotation. Please consult us for
any different application. We cannot be held responsible if the mentioned actuators are used in contradiction to this
advice.
TRANSPORT AND STORAGE
 The forwarding agents being held as responsible for damages and delays of the delivered goods, the consignees are
obliged to express if applicable their reserves, prior to accept the goods. The goods delivered directly ex works are
subject to the same conditions.
 The transport to the place of destination is carried out by using rigid packing material.
 The products must be stored in clean, dry, and ventilated places preferably on appropriate palettes or shelves.
MAINTENANCE
 Maintenance is ensured by our factory. If the supplied unit does not work, please check the wiring according to the
electric diagram as well as the power supply of the concerned electric actuator.
 For any question, please contact our after-sales service.
 To clean the outside of the actuator, use a lint and soapy water: DO NOT USE CLEANING PRODUCT WITH SOL-
VENT OR ALCOHOL
 Before any intervention on the actuator or around the actuator and to prevent from any electrostatic discharge,
the actuator must be cleaned with a damp cloth.
GUARANTEE
 100% of the actuators are fully tested and set in the factory.
 These products are guaranteed two years from the delivery date or 50,000 operating cycles against all types of manu-
facturing and material faults (operating time and model class according to standard CEI34).
 This guarantee will only be valid if the unit has not been disassembled or self-repaired during its service life. It does
not cover any wear and damage caused by shocks or faulty operation neither by the use of the unit under conditions
not in accordance with its nominal characteristics. The guarantee is strictly limited to the replacement of original parts
found defective on checking by our service personnel. The cost of shipping to our premises, the return of devices to
the customer as well as the repair cost will be chargeable. We will not assume the responsibility for any direct or indi-
rect accidents/risks originated by a failure of our products. The guarantee does not cover the consequences of break-
down and excludes any payments for indemnities. The accessories and adaptations are excluded from the guarantee.
In the case where a customer has not proceeded to payments within the agreed period, our guarantee will be sus-
pended until the delayed payments have been received and with the consequence that this suspension will not pro-
long the guarantee period in any case.
RETURN OF GOODS
 The customer is obliged to check the conformity of the goods with regard to their definition at the time of delivery.
 The acceptance of the goods by the purchaser disclaims the supplier of all responsibility if the purchaser discovers
any non-conformity after the date of acceptance. In such case, the repair cost will be borne by the purchaser who will
also exclusively bear all financial consequences of any resulting damage. Returned goods will only be accepted if our
prior agreement has been given to this procedure : the goods must be sent free of all cost and being shipped solely
and in their original packing. The returned goods will be credited to the purchaser with a reduction of 20% on the unit's
price charged in accordance with the original invoice of the returned goods.

SAFETY INSTRUCTIONS

 The electric power supply must be switched-off before any intervention on the electric actuator (i.e. prior demounting
its cover or manipulating the manual override knob). The operator must also be sure that no explosive atmosphere is
present around the actuator before any maintenance operation.
 Any intervention must only be carried out by a qualified electrician or other person instructed in accordance with the
regulations of electric engineering, safety, and all other applicable directives.
 Strictly observe the wiring and set-up instructions as described in the manual: otherwise, the proper working of the
actuator can not be guaranteed anymore. Verify that the indications given on the identification label of the actuator
fully correspond to the characteristics of the electric supply.
- Do not mount the actuator « upside down ».
Risks:
- Do not mount the actuator less than 30 cm of a electromagnetic disturbances source.
4/39
To be read prior to the installation of the product
Declutching mechanism failure
Possible flow of the grease on the electronic board
VALPES
VALVE CONTROL SYSTEM
DSBA3401 - Révision 08/07/2014