Indesit DIF 26 A Bedienungsanleitung Seite 8

Only use products which have been Only use products which have been
Only use products which have been Only use products which have been Only use products which have been
specifically designed for dishwashers. specifically designed for dishwashers. specifically designed for dishwashers. specifically designed for dishwashers. specifically designed for dishwashers.
Do not use table salt or industrial salt, or Do not use table salt or industrial salt, or Do not use table salt or industrial salt, or Do not use table salt or industrial salt, or Do not use table salt or industrial salt, or
washing up liquid. washing up liquid. washing up liquid. washing up liquid. washing up liquid.
If using a multi-functional product it is not necessary to
add rinse aid; however,
Follow the instructions given on the
packaging. If you do not add salt or rinse aid, the LOW
SALT* and LOW RINSE AID* indicator lights remain lit.
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID* indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the
lid (G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure it
does not overflow from the
dispenser. If this happens, clean the
spill immediately with a dry cloth.
F
3. Screw the lid back on.
G
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
• If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
• If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
The appliance is equipped with a water softener which,
by using refined salt designed especially for
dishwashers, supplies water without limescale which is
then used to wash the crockery.
It is possible to adjust the amount of salt used according
to the hardness of the water in your area (this information
is available from your local water board).
- Open the door and switch on the machine by pressing
the ON/OFF button.
- Press the P button and hold for approximately 5
seconds; two short beeps will sound and the indicator
light corresponding to the set degree of hardness will
flash slowly on the control panel (the water softening
system is set to number 3).
- Press the P button repeatedly until the desired
hardness level has been reached (1-2-3-4-5* see Water
hardness table ).
E.g. hardness 1 (indicator light 1 illuminated)
hardness 2 (indicator light 1 illuminated, indicator light 2
flashing)
hardness 3 (indicator lights 1 and 2 illuminated, indicator
light 3 flashing and so on).
- To exit the function, wait approximately 30 seconds or switch off
the machine using the ON/OFF button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
°dH °fH
0 6 0 10
6 11 11 20 1.1
12 17 21 30 2.1
17 34 31 60 3.1
34 50 61 90 6.1
For values between 0°f and 10°f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher ( see Description ) and should be filled:
• When the green float* cannot be seen by simply looking at
the cap of the salt dispenser.
• When the LOW SALT* indicator light on the control panel is
illuminated;
1. Remove the lower rack and
unscrew the cap of the dispenser (in
an anti-clockwise direction).
2. For the first wash cycle only: fill
the dispenser up to the edges with
water.
3. Position the funnel* correctly ( see
figure ) and fill the salt dispenser up
to the edges (approximately 1 kg); it
is normal for a little water to leak out.
4. Remove the funnel, wipe away any salt residue from the
opening and screw the cap on tightly, so that detergent
does not leak into the dispenser during the wash cycle (this
could damage the water softening system beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
mmol/l level
0 1 1
2 2
3 3
6 4
9
*
5