Child Lock; Factory Settings - OJ Electronics ETN4-1999 Bedienungsanleitung

ETN4-1999
Parameter Shown on display
Max. temperature SCA  Hi
Min. temperature SCA  Lo 
Max. limit temperature
Li  Hi
FLOOR *1
Min. limit temperature
Li  Lo  15
FLOOR *1
Frost protection
dEF  8.0
Night setback nSb  -5.0
Measured floor tem-
FLo  24.5 (example) *4
perature
Measured room
ro  21.5 (example) *4
temperature
APp  F
Application
 A
 AF (Room sensor with
 C : Regulator
Scale LCd  C
Temperature reading in
dF  SP
start display
Offset
OFF  0
Control method
PWM  On
PWM cycle time *2 cyc  20
Differential tempera-
dIF  0.3
ture *3
Relay function rEL  no
Software version SU  1.0
*1 : Only available if APp  AF is selected under Application.
*2 : Only available if PWM is ON under Control Method.
*3 : Only available if PWM is OFF under Control Method.
*4 : With no or disconnected sensor, - - is shown on the display.
If Regulator (C) is selected under Application, the floor and room sensors are discon-
nected and heating is controlled on a scale of 0-10, corresponding to 0-100% of full
power.
Max. temperature
The highest temperature to which the thermostat can be set.
Min. temperature
The lowest temperature to which the thermostat can be set.
Max. limit temperature
Allows the highest permissible floor temperature to be set for
wooden and other floor types when control type has been set to
room sensor with floor limit (AF).
Min. limit temperature
Allows the lowest permissible floor temperature to be set for tiled
and other floor types when control type has been set to room sen-
sor with floor limit (AF).
Frost protection
The lowest temperature for frost protection when the function is
activated via an external signal (fig. 4 in instructions).
Example: The setpoint is 25°C.
Frost protection = 8°C means temp. setting = 8°C.
Night setback / energy-saving function
The number of degrees the temperature setting is to be reduced.
The night setback setting must be preceded by a minus sign (-). Is
2

Factory settings

40°C
 40
(-19.5/+70°C)
0°C
0
(-19.5/+70°C)
28°C
 28
(-19.5/+70°C + OFF)
15°C
(-19.5/+70°C + OFF)
8°C
(0/+10°C)
-5°C
(-19.5/+30°C)
(Floor sensor)
F : Floor
(Room sensor)
floor temperature
limits)
C = Celsius
(nU = numerical)
SP = Setpoint
(tP = actual temp.)
0
(+/- 10°C)
On
(OFF)
20 minutes
(10-60 min)
0.3°C
(0.3/10°C)
no = normally open
(nc = normally
closed)
controlled via an external signal (fig. 3 in instructions).
Example: The setpoint is 25°C.
Energy-saving function = -5°C means temp. setting = 20°C.
Energy-saving function = +3°C means temp. setting = 28°C.
Measured floor temperature
Displays actual floor temperature (if a floor sensor is fitted).
Measured room temperature
Displays actual room temperature.
Application
Sets thermostat function. Select the required control type. Four
alternatives exist:
Floor (F):
Room (A):
Room/limit (AF):
Regulator (C):
Scale
Choose between degrees Celsius and a numerical scale. If the
numerical scale is selected, temperature is set on a scale from
0.0 to 10.0 where 0.0 corresponds to min. temperature (SCA Lo)
and 10.0 corresponds to max. temperature (SCA  Hi).
Temperature reading
Defines which temperature is to be shown on the start display: the
setpoint (SP) or the actual, measured temperature.
Offset
If the actual temperature (measured using a thermometer) differs
from that displayed by the thermostat, the thermostat can be
adjusted to offset the difference.
Control method
PWM or ON/OFF control can be selected. PWM is an advanced
control method which calculates the most effective and economi-
cal way to heat homes and other buildings. ON/OFF control is
traditional differential control (e.g. 0.3°C) for other tasks.
PWM cycle time
Allows cycle time to be set when using PWM control. At least 20
min is recommended.
Differential temperature
Allows temperature differential to be set when using ON/OFF con-
trol. The higher the differential temperature, the lower the number
of relay operations.
Relay function
When used for heating purposes, the relay should be in normally
open position (NO). If the thermostat is used for cooling purposes,
the relay should be turned to normally closed (NC).
Software version
Displays thermostat software version.

Child lock

Allows thermostats in public and other places to be locked, thus
preventing unauthorised alteration of the settings. Press and hold
the left- and right-hand buttons simultaneously for 10 seconds. A
symbol indicates that the thermostat is locked.
The child lock can be released by pressing the left- and right-hand
buttons simultaneously for 10 seconds.
Factory settings
Allows factory settings to be restored. Your personal settings will
be deleted from the thermostat.
© 2011 OJ Electronics A/S
The thermostat controls floor temperature
alone.
A floor sensor must be fitted.
The thermostat controls room temperature
alone.
The thermostat controls room temperature
while respecting min. and max. limits for floor
temperature. A floor sensor must be fitted.
The thermostat functions as a simple regulator
and no sensors are used. The setting is in per
cent.
English