Sunn T50C Bedienungsanleitung Seite 4

Your new Sunn® Model
amplifier delivers the power and performance of
the Sunn legacy started in 1964 by the Sundholm
brothers. Crafted and built in California, the
T50C utilizes two pre-amp CHANNELS with sep-
T50C
arate 3-band EQUALIZATION controls and a
PRESENCE control to produce sparkling clean
tones and the screaming distortion that has made
Sunn amps famous! Expand your sonic options
with the T50C's EFFECTS LOOP; separate
T50C
SEND- and RETURN-level controls provide alter-
nate volume-levels for each channel, with or with-
out external effects devices connected.
included FOOTSWITCH allows remote switching
of the EFFECTS LOOP/alternate volume-levels,
as well as CHANNEL selection and ON/OFF
switching of the REVERB effect.
in volume treble bass
channel 1
A B D
C
A. INPUT - Input jack for your guitar.
B. VOLUME - Adjusts the T50C's loudness
1 1 1 1
(speaker output) when using channel-1.
C
C. TREBLE - Adjusts the channel-1 high-
H
frequency level (boost/cut).
A
N
D. BASS - Adjusts the channel-1 low-
N
frequency level (boost/cut).
E
L
E. MIDDLE - Adjusts the channel-1 mid-
1 1 1 1
frequency level (boost/cut).
F. GAIN - Adjusts the channel-2 pre-amplifier
level (distortion at high GAIN settings) sent to
the power-amplifier.
2 2
2 2
VOLUME {J} to set the T50C's overall
volume output.
C
G. TREBLE - Adjusts the channel-2 high-
H
frequency level (boost/cut).
A
H. BASS - Adjusts the channel-2 low-
N
frequency level (boost/cut).
N
E
I. MIDDLE - Adjusts the channel-2 mid-
L
frequency level (boost/cut).
J. VOLUME - Adjusts the power-amplifier level
2 2
2 2 output to the speaker jacks when using
channel-2. NOTE: Use with GAIN {F} to set
the T50C's overall volume output.
SUNN ® MODEL T50C – FEATURES
T50C all-tube guitar
T50C
The
SUNN MODEL T50C - FRONT PANEL
middle gain treble
channel 2
E F G
NOTE: Use with
Need extra power for a large performance? Link mul-
tiple Sunn T50C's together using the MAIN AMP OUT
T50C
and EXTERNAL AMP IN jacks - the VOLUME and 3-
band EQ on the "master"
settings on all of the "clone"
speakers can be connected to the
wide variety of configurations, thanks to the
SPEAKER-LOAD IMPEDANCE switch; Sunn 112
Extension Cabinets were specially designed for use
with the T50C, which can power as many as three
T50C
Sunn 112's linked together! For smaller venues, the
LOW-OUTPUT power setting maintains HIGH-OUT-
PUT tone characteristics at lower volume levels.
Read this manual for instructions on the features
above, along with procedures for testing, balancing
and replacing the T50C's tubes, which are at the
heart of the Sunn Legend.
Sunn Legend
bass middle volume presence
ch select
I J
H K L
K. CHANNEL LED - This light is:
• • ON when channel-2 is active,
• •
• • OFF when channel-1 is active.
• •
L. CHANNEL SELECT - Switch IN for channel-2.
Switch OUT for channel-1. NOTE: This switch is
disabled when the FOOTSWITCH is plugged in.
M. PRESENCE - Adjusts the ultra-high frequency
level of both channel-1 and channel-2.
N. REVERB - Adjusts the REVERB effect level of
both channel-1 and channel-2.
O. STANDBY -
switch for standby mode (power is supplied
only to the tube filaments). Push IN the top-
half of this switch for normal T50C operation.
NOTE: Use standby mode for short breaks to
eliminate warm-up time and increase tube life.
The T50C must be ON for 90-seconds before
the STANDBY switch will function.
P. POWER INDICATOR - This light is ON when
the T50C is receiving power. This light is OFF
when the T50C is not receiving power (or the
bulb has failed). NOTE: Replace bulb by first
switching the T50C OFF, and unplugging the
power cord.
INDICATOR's jeweled cover and replace the
bulb (type T47).
4
T50C control all the same
T50C
T50C's. External loud-
T50C
T50C in a
T50C
reverb
T50C
standby
M N O
Push IN the bottom-half of this
Unscrew the
P
POWER