V2 MR2-U Programmierung Und Installationsanleitung Seite 7

SELECTION OF THE RECEIVER CHANNEL
1. Press P1 push-button of the receiver: L1 led switches on.
2.
Release the push-button, the led switches off and it sends out
a sequence of single flashings for 5 seconds: the number of
short flashings shows the selected channel.
3. To select the further channels press and release the P1
push-button within 5 seconds, the led changes type of
flashing according to the following table:
SELECTED N°
CHANNEL IMPULSES P1
CHANNEL 1 1
CHANNEL 2 2
CHANNEL 3 3
CHANNEL 4 4
PROGRAMMING OF THE MONOSTABLE
FUNCTION
WARNING: If the transmitter is ROYAL, before starting
programming, set the desired code on the transmitter.
Set the same code on all transmitters.
1. Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control.
- if the remote control unit is a ROYAL version, the
procedure ends at point 3
- if the remote control unit is a PERSONAL PASS version, go
to point 4 and follow the procedure until the end of the
section
3.
The LED of the receiver goes off and goes on again for 5
seconds. After 5 second the led goes off: the receiver is ready
to be used
4.
The led of the receiver goes out and goes on again: the code
has been memorised and the receiver remains standby for 5 s
with a new code to be memorised
5. Memorise all the remote control units necessary
6.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
N° Flashing
1 2 3 4
•
•
•
•
- 7 -
PROGRAMMAZIONE DELLA FUNZIONE
BISTABILE
(ROYAL system only)
WARNING: before starting programming, set the desired
code on the transmitter. Set the same code on all
transmitters.
1. Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control
3.
The LED of the receiver goes off and then goes on again:
press the pushbutton P1 of the receiver within 5 sec
4.
Led starts a sequence of flashings at low speed
(1 flash per second)
5.
After the thirtieth flash the led L1 remains on for 5 seconds
6. Press and release the pushbutton P1 within 5 seconds
7. The LED goes off: the receiver is ready to be used
PROGRAMMAZIONE DELLA FUNZIONE TIMER
(ROYAL system only)
WARNING: before starting programming, set the desired
code on the transmitter. Set the same code on all
transmitters.
1. Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control
3.
The LED of the receiver goes off and then goes on again:
press the pushbutton P1 of the receiver within 5 seconds
4. Led L1 starts a sequence of flashings at low speed (1 flash
per second). The number of flashing corresponds to the time
which can be set as shown in the table.
N° Flashing Time
1 01 sec.
2 02 sec.
3 03 sec.
4 04 sec.
5 05 sec.
6 06 sec.
7 07 sec.
8 08 sec.
9 09 sec.
10 10 sec.
11 11 sec.
12 12 sec.
13 13 sec.
14 14 sec.
15 15 sec.
16 30 sec.
5.
Count the number of led L1 flashings corresponding to the
time you wish to set. Press the RX button P1 during the
wished flashing.
6.
The sequence of flashings stops and led L1 goes off:
the receiver is ready to be used.
N° Flashing Time
17 1 min.
18 1,5 min.
19 2 min.
20 2,5 min.
21 3 min.
22 3,5 min.
23 4 min.
24 4,5 min.
25 5 min.
26 5,5 min.
27 6 min.
28 6,5 min.
29 7 min.
30 7,5 min.
31 BISTABLE