auna multimedia 10003601 Bedienungsanleitung Seite 13

1. PRESS THE " PHONO " FUNCTION BUTTON (32) TO ACTIVATE THE TURNTABLE FUNCTION.
2. SET THE 33/45/78RPM SPEED SELECTOR (36) TO THE CORRECT POSITION, DEPENDING
ON THE TYPE OF RECORD TO BE PLAYED.
3. PLACE THE RECORD ON THE TURNTABLE PLATTER - USE THE 45RPM SPINDLE ADAPTOR
(35) IF REQUIRED*.
4. LIFT THE TONE ARM FROM THE ARM REST AND SLOWLY MOVE IT TOWARDS THE RECORD
EDGE. THE PLATTER WILL START ROTATING**.
5. PLACE THE TONE ARM ON THE DESIRED POSITION OF THE RECORD.
6. ADJUST THE VOLUME TO THE DESIRED LEVEL.
7. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING.
8. CAREFULLY LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM REST, SECURING IT AGAIN
WITH THE CLIP WHEN FINISHED.
9. TO MANUALLY STOP THE RECORD, LIFT THE TONE ARM CAREFULLY AND RETURN IT TO THE ARM REST.
NOTE: TO PLAY A 45RPM RECORD WITH THE CENTRE CLIP MISSING, FIRST PLACE THE SUPPLIED 45RPM ADAPTOR
(35) ONTO THE SPINDLE. THIS WILL NOT BE NECESSARY IF THE CENTRE CLIP OF THE RECORD IS STILL IN PLACE.
AUTO-STOP FUNCTION
SOME LONGER VINYL RECORDS WILL STOP PLAYING BEFORE THE LAST TRACK HAS FINISHED, AS THE AUTO-
STOP AREA IS SET OUTSIDE THE AREA PRE-SET FOR THE UNIT. IF THAT IS THE CASE, MOVE THE AUTO-STOP
ON/OFF SWITCH (41) ON THE REAR OF THE UNIT TO THE "OFF" POSITION, THE TONE ARM WILL THEN CARRY
ON PLAYING TO THE END OF THE RECORD. HOWEVER, THE TURNTABLE WILL CONTINUE ROTATING AND WILL
NOT STOP AUTOMATICALLY. TO STOP THE TURNTABLE ROTATING, TURN THE UNIT OFF (9) OR SWITCH THE
AUTO-STOP SWITCH BACK TO THE "ON" POSITION, THEN RETURN THE TONE ARM TO ITS REST.
**NOTE: WITH THE AUTO-STOP SWITCH (41) SET AT THE "OFF" POSITION, THE TURNTABLE WILL START ROTATING
AS SOON AS PHONO FUNCTION IS SELECTED.
STYLUS REPLACEMENT
WHEN THE STYLUS EVENTUALLY NEEDS REPLACING, A UNIVERSAL SAPPHIRE NEEDLE OR STYLUS (FOR
45/33/78RPM RECORDS) IS AVAILABLE FOR PURCHASE DIRECT FROM THE MANUFACTURER. PLEASE CON-
TACT YOUR SUPPLIER OR STEEPLETONE PRODUCTS DIRECT FOR INFORMATION ON HOW TO PURCHASE ONE.
TO REMOVE THE STYLUS FROM THE TONE ARM, HOLD THE TONE ARM HEAD STEADY WHILE GRABBING THE
PLASTIC STYLUS HOLDER WITH TWO FINGERS - THEN GENTLY PULL THE COMPLETE STYLUS HOLDER TO-
WARDS YOU AND OFF THE BLACK TONE ARM CARTRIDGE, AS SHOWN IN THE LINE DRAWING.
TO REPLACE THE STYLUS, HOLD THE SIDES OF THE RED PLASTIC STYLUS HOLDER, ENSURING THE NEEDLE IS
FACING DOWNWARDS. GENTLY PUSH THE BACK OF THE STYLUS HOLDER AGAINST THE CARTRIDGE AT THE
END OF THE TONE ARM AND CLIP IT UPWARDS INTO PLACE, UNTIL YOU ARE SURE IT IS SECURELY FITTED.
COVER IT WITH THE PROTECTIVE NEEDLE COVER, IF SO REQUIRED.
NOTE: ALWAYS HANDLE THE STYLUS WITH CARE AS THE SAPPHIRE NEEDLE TIP IS EASILY DAMAGED. WHEN
TRANSPORTING THE TURNTABLE IT IS ADVISABLE TO TURN DOWN THE PROTECTIVE NEEDLE COVER UNTIL THE
UNIT IS GOING TO BE USED AGAIN. WHEN REMOVING OR RE-FITTING THE STYLUS, ALWAYS BE CAREFUL NOT
TO PUT TOO MUCH PRESSURE ON THE STYLUS HOLDER AND THE TONE ARM CARTRIDGE, TO AVOID CAUSING ANY
POSSIBLE DAMAGE TO THEM.
13 13