Siemens REV16 Installationsanleitung Seite 4

Taste hinter der Nadelöffnung zusammen mit der Wärmer-
und Kältertaste mindestens eine Sekunde drücken.
Nach diesem Reset werden die Werkseinstellungen neu
geladen (siehe auch Abschnitt „Werkseinstellungen" in der
Bedienungsanleitung).
8 Hinweise
• REV16 ist ein elektronischer Raumtemperaturregler mit
Wochenschaltuhr.
• Der Regler gehört zur Softwareklasse A und ist für den
Gebrauch in einer Umgebung mit normalem
Verschmutzungsgrad vorgesehen.
Commissioning
1 Mounting
Remove controller from its base by proceed according to
Fig. A.
For mounting, refer to Figs. B and C and "Mounting notes".
2 Check wiring
For the electrical connections, refer to "Connection
diagram" (also refer to Fig. D).
Note: do not use stranded wires, only solid wires or
stranded wires with ferrules.
3 Remove the battery transit tab
As soon as the battery transit tab is removed, the controller
starts to operate (also refer to Figs. E).
4 Configuration
4.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by
rolling the roller selector away from the display and then
toward the display (also refer to Fig. G).
4.2 Functions
4.2.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol
will flash. When pressing the roller selector, the room
temperature currently measured flashes and can now be
recalibrated by a maximum of ± 2 °C by rolling either
toward the display or away from it. To store the re-
calibration, press the roller selector (also refer to Fig.
4.2.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing
CAL symbol to the setpoint limitation symbol by rolling
toward the display. (also refer to Fig.
Press to accept. 5...29 °C will flash (factory setting). Press
to accept or continue rolling.
Setting 16...29 °C will flash.
Press to accept.
4.2.3 Control mode
On the heating engineer level, change from the flashing
CAL symbol to the symbols of the various control modes
by rolling away from the display (also refer to Fig.
Press to accept. (factory setting) will flash. Press
to accept (Fig. 3) or continue rolling toward the display to
select one of the following control modes:
4/18
• Sollten im Referenzraum thermostatische
• Der Fernbedienungskontakt muss getrennt, d.h. mit
• Die örtlichen Vorschriften für Elektroinstallationen sind
required control mode.
A brief description of the control modes is given below
(also refer to Fig.
PID 12 Normal controlled systems:
PID 6
4.2.4
This function protects the pump against seizing during
longer off periods. Periodic pump run is activated for a
minute every 24 hours at 12:00 (when pump run is activa-
ted, the flame symbol
On the heating engineer level, change from the flashing
CAL symbol to the
the display (factory setting, periodic pump run off). Press to
accept.
continue rolling. The
will flash. Press to accept.
4.2.5
).
Use operating mode selector
the standard value of 5 °C need to be changed, the frost
protection setpoint
menu T (refer to the Operating Instructions and also to
Fig.
5
Proceed according to Fig. F.
).
6
a) Check the display. If there is no display, check the
b) Comfort mode
c) Select temperature menu T and adjust the temperature
).
d) The relay must be energized and thus the actuating
29.08.2002
Heizkörperventile installiert sein, müssen diese
vollständig geöffnet werden
einem separaten, abgeschirmten Kabel verdrahtet
werden
einzuhalten
, PID 6, PID 12 or
).
Self-learning, adaptive control:
Suited for all standard applications (factory
setting).
For locations with normal temperature variations.
Fast controlled systems:
For locations with significant temperature
variations.
Difficult controlled systems:
Proper on / off controller with a switching
differential of 0.5 C.
Periodic pump run
symbol by rolling once away from
will flash (factory setting). Press to accept or
symbol for periodic pump run on
Frost protection mode
must be changed via temperature
).
Replacing the controller on its base
Functional check
correct fitting and function of the batteries.
setpoint to 29 °C (refer to the Operating
Instructions)
device activated within one minute. Flame symbol
will appear on the display. If that is not the case:
. Press to accept the
appears on the display).
to select symbol . If
CE1G2257xx