TermaTech TT30 Montage- Und Bedienungsanleitung Seite 23

1. The damper/start-up device can be opened (the knob is pushed down and to the right) for a
few minutes at lighting. Put about 10 kindling sticks (dia. 2-3 cm) in the bottom of the stove, laid
2. Leave the door ajar so there is an opening of about 2-3 cm. Leave the stove like that for about
8-10 minutes before you close the door completely. Stay by the stove as long as the door is ajar.
To set the door "ajar" there is a small "door stop mechanism" at the bottom of the door, which
can easily be turned outwards so as to ensure that the door does not close completely. After 8-10
minutes, open the door and turn the "door stop mechanism" back into place. The door will now
close tightly into the stove. See drawing 4 (page 23)
3. When the fire has burned to embers (there are no more flames) open the door gently so the
ash is not whirled out through the door. Gently spread out the embers with a poker so they are
even.
4. Put 2-3 pieces of firewood in the stove, about 1.7 kg total. The pieces are put in the bottom of
the stove and parallel to the front of the stove with equal distance to the stove's sides and with
mutual distance of about 1 cm. The front piece is best lit if it has a split side that is turned to the
door and one in the embers. Close the door completely immediately.
5. The knob/damper is opened so it is about 2/3 open (between the left and middle position)
and after about 2 minutes the damper is set to about 1/3 open. How much the damper should be
6. When the wood has burned to embers (after about 45-60
minutes) you start again from point 3.
MAINTENANCE – always use original parts
Maintenance and cleaning of the stove should only be performed when the stove is cold. The daily
Lighting and continuous firing at EN-testing
maintenance is limited, but once a year the stove should get thorough maintenance. The combu-
stion chamber should be cleaned for ashes and soot and the door hinges and the closing mecha-
nism should be lubricated with copper grease.
in a criss-cross pattern as a log house. Put 2 firelighters in the middle and light them.
The surface is maintained by brushing it with a soft, long-haired brush or by using the vacuum
cleaner with a brush.
The stove can also be dusted with a duster. Always remember: only when the stove is cold.
Jointings can look okay, but they collapse under the heat and thereby lose the ability to keep the
stove sealed. Jointings should be changed as needed as it is important to good combustion and a
clean window that the stove is sealed.
The insulation plates in the combustion chamber that are broken or worn can easily be chan-
However, it should be changed when the wear surpasses half of the original thickness. See dra-
wing 5+6 (page 7)
Painting the stove with Senotherm-spray can cover spots or small scratches from kettles and
The can has to be shaken vigorously and then sprayed on at a distance of 15-20 cm. It is very
hazard. In order to keep the stove's varnished surfaces looking nice for years to come you should
ventilation when using spray paint.
open depends on the individual chimney's draught, but the flames should now stabilise to a calm
fire.
Glass normally does not need any maintenance apart from cleaning. This is most easily done by
using TermaTech's glass cleaner. Remember only to use glass cleaner when the stove is cold. The
TT30G, which is furnished with side glass/windows, has no air-wash system on its side glass/win-
dows. Hence they can become sooty more often, and possibly will require more frequent cleaning.
Original parts which need to be changed due to wear can be found at your dealer. Because of fit
etc. only original parts from TermaTech should be used.
Right to claim compensation for defective product is under current law.
When stating deviations the use of the product must be suspended immediately and the dealer
must be contacted.
ged as they are loosely fixed. The material used is called Vermiculite and is a porous, but very
23
suitable insulation material. It has no effect on the stove's efficiency that the insulation cracks.
such. Larger damages needs to be ground with fine steel wool, vacuumed and then sprayed.
important that the stove is not in use and completely cold before you use the spray due to the fire
try to avoid touching the varnished surfaces when the stove is hot. Make sure to have sufficient