Fluval 07 Serie Benutzerhandbuch Seite 6

To ensure optimal and proper functioning of your 07 Series Fluval External Filter, regular maintenance is required. Failure to do so
may result in the failure of the filter and will invalidate your warranty. Additionally, regular cleaning and maintenance will greatly
reduce or completely prevent faults and reduction in performance. Please refer to the maintenance schedule below.
COMPONENTS
Magnetic Impeller & Impeller Well 1,4,6
Ceramic Shaft
4
Intake Stem/Strainer
3
Ribbed Hosing
Primer Assembly with Primer Cover
Motor Head Gasket
2, 5
AquaStop O-ring Gaskets
Quick Clear
Bio-Foam
Bio-Foam+
Bio-Foam Max
BIOMAX
Pre-Filter
BIOTERRA
Carbon
Ammonia Remover
Zeo-Carb
Phosphate Remover (Pad)
Nitrite Remover (Pad)
Ammonia Remover (Pad)
To ensure constant presence of beneficial bacteria, never replace all media at the same time.
1. Ensure Impeller Cover is fitted right way up when replacing.
2. Lubricate Motor Head ("O" Ring) gasket using an inert lubricant
(i.e. Fluval Silicone Lubricant #A325 or vegetable oil). Do NOT use
petroleum jelly based products.
3. Pipes will gradually block with protein slime and waste.
MODEL
AQUARIUM*
PUMP PERFORMANCE
VERTICAL PRE-FILTER
BASKET VOLUME
TOTAL CHAMBER VOLUME
CANISTER VOLUME
FILTER DIMENSIONS
FILTER CIRCULATION**
MAX WATER COLUMN HEIGHT
WATTAGE – 120V/60Hz:
WATTAGE – 230-240V/50Hz:
*Aquarium recommendations are based on North American (US Gal) or European (L) standard aquarium usage
**Flow rates were measured with intake and output hoses of the same length
IMPORTANT
RECOMMENDED MAINTENANCE FREQUENCY
MONTHLY
Check & Clean
Check & Clean
Clean & Lubricate
Replace
Check & Clean
Check & Clean
Check & Clean
Rinse with aquarium water
Rinse with aquarium water
Replace
Replace
Replace
Replace
Replace
Replace
107 207
10-30 US Gal 20-45 US Gal
40-130 L 60-220 L
145 US Gal/h 206 US Gal/h
550 L/h 780 L/h
514 cm2 803 cm2
1.2 L 1.8 L
2.0 L 3.1 L
3.9 L 5.3 L
7.5" x 7" x 13.7" 7.5" x 7" x 16.5"
19 x 18 x 35 cm 19 x 18 x 42 cm
95 US Gal/h 121 US Gal/h
360 L/h 460 L/h
1.45 m 1.45 m
10 W 10 W
EN-3
EVERY 3 MONTHS EVERY 6 MONTHS
Check & Clean
Clean & Lubricate
Clean & Lubricate
Replace
Replace
Replace
Replace Half Quantity
Replace Half Quantity
Replace Half Quantity
4. Yearly replacement ensures optimal performance.
5. The Motor Head Gasket ("O" Ring) will deteriorate over time and
must be replaced yearly to avoid the potential for leaks.
6. Impeller will wear out over time. As a preventative step, replace
yearly.
307
40-70 US Gal
90-330 L
303 US Gal/h
1150 L/h
803 cm2
3.1 L
4.5 L
7.3 L
9.5" x 7" x 16.5"
24 x 18 x 42 cm
206 US Gal/h
780 L/h
1.75 m
16 W
15 W
YEARLY
Replace (Impeller only)
Replace
Check & Clean
Replace
407
50-100 US Gal
150-500 L
383 US Gal/h
1450 L/h
1074 cm2
4.2 L
6.0 L
9.2 L
9.5" x 7" x 19.3"
24 x 18 x 49 cm
245 US Gal/h
930 L/h
2.25 m
23 W
20 W