Ryobi ERT-2100V Bedienungsanleitung Seite 22

GB
F D
ADJUSTMENTS
To make deeper cuts it is therefore necessary to make as
many successive passes as required, lowering the bit
1/8 in. (3.2 mm) for each new pass. In order to save time,
do all the cutting necessary at one depth setting, before
lowering the bit for the next pass. This will also assure a
uniform depth when the final pass is completed.
TO ADJUST DEPTH OF CUT (Fig. 5-7)
Loosen the stop bar (9).
■
Unlock (U) the plunge lock lever (14) by turning it
■
counter clockwise.
Lower the router body until the cutter is in contact
■
with the work-piece.
Lock the depth stop (8) at the right height.
■
Set the exact depth of cut using the graduation.
■
The distance between the stop bar (9) and screw of
the depth stop (8) is setting plunge depth.
Tighten the stop bar lock knob (10) to set depth of
■
plunge.
DEPTH STOP (Fig. 8 & 9)
The depth stop (8) can be used to set three different
■
depths. This is par ticularly useful for deep cut,
performed in steps.
If required, set all three screws.
■
VARIABLE SPEED CONTROL SELECTOR
(Fig. 10)
Your router has a variable speed control selector (2)
designed to allow operator control of speed and torque
limits. You can make speed selections best suited to the
type of cut, the material being cut, and the size of bit being
used. The variable speed control selector allows you to
adjust router speed from 8,000 to 23,000 min
six step scale (1 to 6) on the variable speed control
selector. To increase the speed and torque of your router,
turn the variable speed control selector to a higher setting
(6). Turn to a lower setting to decrease speed and torque.
Note: If you do not want to use the variable speed control
selector, turn it to the highest possible setting, and the
feature will not be active.
We suggest that you practice with the variable speed
feature of your router before installing a cutter and
making cuts in wood.
E I P NL
-1
S DK N FIN GR
English
ZERO RESET INDICATOR
The zero reset indicator allows you to use the scale
provided on the housing to make quick depth of cut
changes to existing depth of cut settings. Simply choose
a reference point on the scale and slide the zero reset
indicator up or down the scale the distance required for
new depth of cut. Then change stop bar position by
loosening lock knob and adjusting stop bar until red line
on zero reset indicator moves back to reference point.
Tighten lock knob securely to lock stop bar in new
position. The cutter position will now increase or
decrease the exact distance the stop bar was adjusted.
OPERATION
SWITCH (Fig. 11)
To turn the router ON, press the lock-off button (4) and
squeeze the switch (15). To turn the router OFF, release
both the switch & lock-off button.
ROUTING (Fig. 12)
For ease of operation and maintaining proper control,
your router has two handles (3), one on each side of the
router base. When using your router hold it firmly with
both hands.
Before starting the router, unplug it and make sure the
cutter is securely tightened in collet nut and that depth of
cut is properly set.
Plug router into power supply, turn it on, and let motor build
to its full speed, then gradually plunge or feed cutter into
workpiece. Do not let the cutter contact workpiece before
turning on router and allowing it to develop full speed.
. There is a
Remain alert and watch what you are doing. Do not
operate router when fatigued or under the influence of
drugs, alcohol, or any medication.
ROUTING GROOVES (Fig. 13)
When routing across the face of boards, set router at
desired depth of cut, place the edge of router base
against workpiece, and turn on the router. Slowly feed the
cutter into the workpiece along desired line of cut.
16
H CZ RUS
CAUTION
We suggest that you practice with your router
before installing a cutter and making cuts in wood.
WARNING
If desired depth of cut is greater than can be safely
cut in one pass, make cuts in two or more passes.
RO HR
PL SLO TR