Ryobi ERT-2100V Bedienungsanleitung Seite 18

GB
F D
GENERAL SAFETY RULES
SERVICE
Tool service must be performed only by qualified
■
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical
■
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance
Instructions may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when
■
performing an operation where the cutting tool
may contacthidden wiring or its cord. Contact with
a "live" wire will make exposed metal parts of the tool
"live" and shock the operator.
ADDITIONAL SAFETY RULES
Know your power tool. Read operator's manual
■
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear safety glasses. Everyday eyeglasses
■
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
Protect your lungs. Wear a face or dust mask if the
■
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection
■
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged,
■
have repaired at your nearest Factory Service Center
or other Authorized Service Organization.
Constantly stay aware of cord location. Following
■
this rule will reduce the risk of electric shock or fire.
Check damaged parts. Before further use of the
■
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function.Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by
an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
E I P NL S DK N FIN GR
English
Do not abuse cord. Never carry the tool by the cord
■
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges. Following
this rule will reduce the risk of electric shock or fire.
Inspect for and remove all nails from lumber
■
before routing. Following this rule will reduce the risk
of serious personal injury.
Drugs, alcohol, medication. Do not operate tool
■
while under the influence of drugs, alcohol, or any
medication. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Save these instructions. Refer to them frequently
■
and use them to instruct others who may use this tool.
If you loan someone this tool, loan them these
instructions also.
SPECIFICATIONS
Voltage
No load speed
Input power
Plunge depth
Collet size
Peak horsepower
Net weight
DESCRIPTION
1. LED light
2. Variable speed control
3. Handle
4. Lock-off button
5. Spindle lock button
12
H CZ RUS
WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm.
Some examples of these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and
other masonry products, and
- arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and work with
approved safety equipment, such as those dust
masks that are specially designed to filter out
microscopic particles.
230 V ~ 50 Hz
8000-23000 min-
2100 W
60 mm
8 mm and 12 mm
1.3 HP
6.33 kg
RO HR
PL SLO
1
TR