General Safety Rules - Ryobi ERT-2100V Bedienungsanleitung

GB
F D

GENERAL SAFETY RULES

SAVE THESE INSTRUCTIONS.
WARNING
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
WORK AREA
Keep your work area clean and well lit. Cluttered
■
benches and dark areas invite accidents.
Do not operate power tools in explosive
■
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools may
create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away
■
while operating a power tool. Distractions can
cause you to lose control.
ELECTRICAL SAFETY
Avoid body contact with grounded surfaces,
■
such as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
Do not expose power tools to rain or wet
■
conditions. Water entering a power tool will increase
the risk of electric shock.
Do not abuse the cord. Never use the cord to carry
■
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
Use outdoor extension leads. When tool is use
■
outdoors, use only extension cords intended for
outdoor use.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
■
common sense when operating a power tool.
Do not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose clothing or
■
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts or
drawn into air vents.
E I P NL S DK N FIN GR
English
Avoid accidental starting. Be sure switch is off
■
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch on,
invites accidents.
Remove adjusting keys or wrenches before
■
turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
Do not overreach. Keep proper footing and balance
■
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Do not use on a ladder or unstable support.
Use safety equipment. Always wear eye protection.
■
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Connect dust extraction equipment. If devices are
■
provided for the connected extraction and collection
facilities ensure these are connected and properly used.
TOOL USE AND CARE
Use clamps or other practical way to secure and
■
support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
Use the right tool. Do not force small tools or
■
attachments to do the job of a heavy duty tool. Do not
use tool for purposes not intended.
Do not use tool if switch does not turn it on or off.
■
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from power source before
■
making any adjustments, changing accessories,
or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
Store idle tools out of the reach of children and
■
other untrained persons. Tools are dangerous in the
hands of untrained users.
Maintain tools with care. Keep cutting tools sharp
■
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving
■
parts, breakage of parts, and any other condition
that may affect the tool's operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
Only use cutters of the correct shank diameter and
■
which are suitable for the speed of the tool.
Use only accessories that are recommended by
■
the manufacturer for your model. Accessories that
may be suitable for one tool, may become hazardous
when used on another tool.
11
RO
H CZ RUS
HR
PL SLO TR