Auto Scanning Function; Wind Speed And Direction - Oregon Scientific WMR112 Bedienungsanleitung

To clear the memory,
1. Press the outdoor/channel humidity window.
2. Press [CHANNEL] for the outdoor thermo-hygrometer or the
desired channel.
3. Press and hold [MEMORY] till a key tone is heard.
4. Press [MEMORY] to check if the memory is clear.

AUTO SCANNING FUNCTION

The auto scanning function is avalibable for the outdoor/channel
window for both the temperature and humidity.
To use it,
1. Press the outdoor/channel temperature or humidity window.
2. Press and hold [ ] until another key tone is heard. The main unit
will start scanning from the active temperature and humidity
display. Each channel will be displayed for about 4 seconds.
To exit the auto scanning routine, press any window or control
button.
RAINFALL
The rate of rainfall can be displayed in mm/hr or in/hr.
To select the display unit,
1. Press the rainfall window.
2. Press [UNIT] for the desired setting.
To display the yesterday's rainfall and the total rainfall from the last
cleared date,
1. Press the rainfall window.
2. Press [MEMORY] for the desired record. Yesterday rainfall will
be displayed with "YESTERDAY" shown in the rainfall window.
Total rainfall will be displayed with "TOTAL" shown in the
rainfall window. The time and date of the record will be displayed
alternatively with "SINCE" icon in the clock window for total
rainfall.
Note: Yesterday's rainfall record will be updated when the real time
clock runs from 11:59:59 pm to 12:00:00 am. And it is counted for
12:00:00 am of one day to 12:00:00 am on the next day.
If the rain sensor detects no rainfall for about two consecutive hours,
the current rate of rainfall will be displayed as zero.
To clear the total rainfall,
1. Press the rainfall window.
2. Press and hold [MEMORY] till a key tone is heard.
The yesterday's rainfall record will not be affected when you clear
the total rainfall.

WIND SPEED AND DIRECTION

The current wind speed and direction are displayed in the wind
speed and direction window.
To display the average wind speed, press the window till the
"AVERAGE" icon is displayed.
The wind speed can be displayed in m/s, kph, mph or knots.
To select the display unit,
1. Press the wind speed and direction window.
2. Press [UNIT] for the desired setting.
To display the maximum speed and direction for gust wind in
record,
1. Press the wind speed and direction window.
2. Press [MEMORY]. The time and date of the record will also be
displayed aternatively with "STAMP" icon in the clock window.
To clear the record,
1. Press the wind speed and direction window.
2. Press and hold [MEMORY] till a key tone is heard.
As for the wind direction, it is displayed in a digital compass with
bearing read-outs.
WEATHER ALARMS
Weather alarms are used to alert you to certain weather conditions.
Once activated, the alarm will go off when a certain set of criterion
is met.
You can set alarms for:
• Indoor, outdoor and channel high temperatures
• Indoor, outdoor and channel low temperatures
• Indoor, outdoor and channel dew point approaching
• Indoor, outdoor and channel high humidity
• Indoor, outdoor and channel low humidity
• High rainfall rate
• Pressure drop
• High gust wind
• Low wind chill
To set a weather alarm,
1. Press the window containing the weather element you want to
set.
2. Press [ALARM]. The current alarm setting will be displayed.
3. Press and hold [SET].
4. Press [ ] and [ ] for the desired setting.
5. Press [SET].
For temperatures and humidity, the high and low alarms can be set
in sequence. After entering the value for one alarm, you will be
prompted to enter the value for the other.
A weather alarm is activated once set. When the set criteria are met,
an alarm will go off and the current reading will flash together with
the corresponding indicator.
If that happens in the outdoor/channel temperature or humidity
window, the "OUT" indicator will flash to show that the criteria set
for the outdoor thermo-hygrometer have been met. If it is one of the
separate sensors, the [CHANNEL] indicator will flash. Press the
window repeatedly to locate the channel in question.
When a weather alarm goes off, press any button to stop the alarm.
The alarm is still active until you deactivate the function or the
criteria are no longer met.
7