Set Altitude; Rainfall; Accumulated Rainfall; Weather Forecast - Oregon Scientific WMR200 Bedienungsanleitung

To select clock display mode:
Press clock area repeatedly to toggle between:
• Clock with seconds
• Clock with weekday
• Date with year
• Data logger (please refer to Memory / Data logger section)
PRESSURE
To toggle barometer unit:
1. Press barometer area to toggle between Altitude / current barometer.
2. Press UNIT to select FEET / M or inHg / mmHg / mb / hPA.

SET ALTITUDE

Set the altitude to reflect distance from sea level at your position.
1. Press barometer area to display ALT.
2. Press SET.
3. Press UP / DWN to set the altitude in 10 m (33 ft) increments from -100 m (-328
ft) to 2500 m (8202 ft).
4. Press SET or touch panel area (except tool bar / forecast area) to confirm.

RAINFALL

To select rainfall display mode:
Press rain area to toggle between:
• Rain rate
• Hourly Rainfall
•

Accumulated rainfall

• Rainfall recorded in the past 24 hours
Press UNIT to select mm / in.
ACCUMULATED RAINFALL
To display SINCE DATE:
1. Press rain area repeatedly until Accumulated Rainfall is displayed. (Clock
area will display the start date / time of rainfall recording).
To reset SINCE DATE:
Press and hold MEM to set current time as start of accumulated rainfall records.
UV
The UV index levels are as follows:
UV INDEX DANGER LEVEL
0-2 Low
3-5 Moderate
6-7 High
8-10 Very high
11 and above Extremely high

WEATHER FORECAST

This product forecasts the next 12 to 24 hours of weather within a 30-50 km (19-31
mile) radius (US- with a 75% accuracy).
Sunny
Clear night
Partly cloudy
Partly cloudy at night
Cloudy
Rainy
Snowy

TEMPERATURE AND HUMIDITY

To toggle temperature unit:
1. Press Indoor / Outdoor
ICON
Temperature / Humidity area.
2. Press UNIT to select °C / °F.
To auto-scan between sensors (Outdoor):
1. Press Outdoor Temperature / Humidity area.
2. Press and hold CH to display data for each sensor.

AUTO SCANNING FUNCTION

To activate the outdoor temperature and humidity auto-scan function:
1. Press and hold CH to activate auto-scan. The temperature and humidity display
will scroll from indoor to ch1 through to ch10.
2. Press CH / MEM to stop the auto-scan.
NOTE Channel 1 is used for the outdoor temperature and humidity sensor provided in
this package. Additional temperature and humidity sensors can use other channels.
To change channel:
Press CH to change channel.

TEMPERATURE AND HUMIDITY TRENDS

The temperature and humidity trend icons are based on recent sensor readings.
The trend lines are shown next to the temperature and humidity readings. The trend
is shown as follows:
RISING

HEAT INDEX

Press Indoor / Outdoor
temperature felt:

TEMPERATURE

WARNING
RANGE
27°C to 32°C
Caution
(80°F to 89°F)
32°C to 40°C
Extreme Caution
(90°F to 104°F)
41°C to 54°C
Danger
(105°F to 129°F)
54°C to 92°C
Extreme danger
(130°F to 151°F)
NOTE Heat index is only calculated when temperature is 80° F / 27°C or above.

WIND

To select wind display mode:
Press wind area to toggle between:
• Gust
• Average
Press UNIT to select unit: knots / kph / mph / m/s.
The wind level is shown by a series of icons:
Lost
Light
sensor
0-8 mph
(3-13 km/h)

MOON PHASE

1. Press clock area to activate.
2. Press SET repeatedly to display Year / Calendar date.
3. Press UP / DWN to view moon phase for specific dates.
New Moon
Waxing Crescent
First quarter
8
STEADY FALLING
Temperature / Humidity area to display the actual
MEANING
Possibility of heat exhaustion
Possibility of heat dehydration
Heat exhaustion likely
Strong risk of dehydration / sun
stroke
Moderate Strong Storm
>55 mph
9-25 mph 26-54 mph
(14-41 km/h) (42-87 km/h)
(>88 km/h)
Full Moon
Waning Gibbous
Last quarter