Technical Data; Noise/Vibration Information; Battery Charging - Bosch 3 603 CD3 1 Series Originalbetriebsanleitung

OBJ_BUCH-2850-003.book Page 20 Monday, June 19, 2017 12:15 PM
20 | English

Technical Data

Angle Grinder
Article number
Rated voltage V=
-1
Rated speed min
Speed control
-1
adjustment min
Grinding disc diameter,
max. mm
Thread of grinder
spindle
Thread length (max.) of
grinder spindle mm
Constant electronic
control
Speed preselection
Soft starting
Restarting Protection
Overload Protection
Weight according to
EPTA-Procedure
01:2014
– with vibration-damp-
ing auxiliary handle kg
– with standard-auxil-
iary handle kg
Permitted ambient
temperature
– during charging °C
**
– during operation
and during storage °C
Recommended
batteries
Recommended
chargers
– for PBA 18V ...W–B,
PBA 18V ...W–C
– for PBA 18V ...V– .
* depending on the battery pack being used
** limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 80 dB(A); Sound power level 91 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
1 609 92A 2LJ | (19.6.17)
Vibration total values a
determined according to EN 60745-2-3:
AdvancedGrind 18
Surface grinding: a
3 603 CD3 1..
Disk sanding: a
18
The vibration level given in this information sheet has been
10000
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
2800 – 10000
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
125
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
M 14
may significantly increase the exposure level over the total
working period.
22
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
 when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the
 accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
*
2.7 (2.5 Ah)–3.2 (6.0 Ah)

Battery Charging

 Use only the chargers listed in the technical data. Only
*
2.4 (2.5 Ah)–3.0 (6.0 Ah)
Note: The battery supplied is partially charged. To ensure full
0...+45
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
–20...+50
The lithium-ion battery can be charged at any time without re-
PBA 18V ...W–B
ducing its service life. Interrupting the charging procedure
PBA 18V ...W–C
does not damage the battery.
PBA 18V ...V–.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
AL 18.. CV
 Do not continue to press the On/Off switch after the
AL 22.. CV
AL 18.. CV
Observe the notes for disposal.
Removing the battery
(triax vector sum) and uncertainty K
h
2
=6.5 m/s , K=1.5 m/s
h
2
=5.0 m/s , K=1.5 m/s
h
these chargers are matched to the lithium-ion battery of
your power tool.
machine has been automatically switched off. The bat-
tery can be damaged.
2
,
2
.
Bosch Power Tools