Maintenance - Chicago Pneumatic CP3000-F Serie Bedienungsanleitung

EN
English
INSTRUCTION MANUAL
Machine Type:
Pneumatic tool equipped with 1/4" collet chuck for
use with various burrs for grinding - No other use is
permitted
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air.
Higher pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting
sizes shown in the diagram below.
3. Do not install a quick coupler directly into the
grinder throttle handle.
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted
to two drops per minute. If an air line lubricator
cannot be used, add air motor oil to the inlet once a
day.

Maintenance

1. Disassemble and inspect tool every three months
if the tool is used every day. Replace damaged or
worn parts.
2. High wear parts are underlined in the parts list.
Technical Data
Collet diameter: 1/4" - 6.35mm
Air pressure 90 psi (6.3 bar)
Original Instructions
Copyright 2012, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the
contents or part thereof is prohibited. This applies in particular to
trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused
by the use of unauthorized parts is not covered by Warranty or
Product Liability.
Noise & Vibration Declaration*
Tool Vibration*
(m/s²)
CP3000-325F 3,2 - k= 1,6
CP3000-330F <2,5
CP3030-325F <2,5
CP3030-330F <2,5
CP3000-415F <2,5
CP3000-418F <2,5
CP3000-420F <2,5
CP3000-424F <2,5
CP3030-418F <2,5
CP3030-420F <2,5
CP3030-424F <2,5
CP3000-515F <2,5
CP3000-518F <2,5
CP3000-520F <2,5
CP3030-518F <2,5
CP3030-520F <2,5
*re. ISO 20643
** uncertainty 3 dB(A), in accordance with EN ISO15744. For sound power, add 11
dB(A).
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the
latest information please visit cp.com.
These declared values were obtained by laboratory type testing
in accordance with the stated standards and are suitable for
comparison with the declared values of other tools tested in
accordance with the same standards. These declared values
are not adequate for use in risk assessments and values
measured in individual work places may be higher. The actual
exposure values and risk of harm experienced by an individual
user are unique and depend upon the way the user works,
the workpiece and the workstation design, as well upon the
exposure time and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of values
reflecting the actual exposure, in an individual risk assessment
in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is
not adequately managed. An EU guide to managing hand-arm
vibration can be found at www.pneurop.eu/uploads/documents/
pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf
We recommend a programme of health surveillance to
detect early symptoms which may relate to noise or vibration
exposure, so that management procedures can be modified to
help prevent future impairment.
MANUFACTURER'S LIMITED WARRANTY
Limited Warranty: The "Products" of the Chicago Pneumatic Tool Co. LLC
("CP") are warranted to be free from defects in material and workmanship
for one year from the date of purchase. This Warranty applies only to
Products purchased new from CP or its authorized dealers. Of course,
this Warranty does not apply to products which have been abused,
misused, modified, or repaired by someone other than CP or its Authorized
Service Representatives. If a CP Product proves defective in material or
workmanship within one year after purchase, return it to any CP Factory
Service Center or Authorized Service Center for CP tools, transportation
prepaid, enclosing your name and address, adequate proof of date of
purchase, and a short description of the defect. CP will, at its option, repair
or replace defective Products free of charge. Repairs or replacements are
warranted as described above for the remainder of the original warranty
period. CP's sole liability and your exclusive remedy under this Warranty
is limited to repair or replacement of the defective Product. (There Are No
Other Warranties Expressed Or Implied And CP Shall Not Be Liable
For Incidental, Consequential, Or Special Damages, Or Any Other
Damages, Costs Or Expenses Excepting Only The Cost Or Expense Of
Repair Or Replacement As Described Above.)
CP3000-F Series
CP3030-F Series
7° Angle die-grinder
Sound Air Cons. Speed
pressure
level**
(dBa) (cfm - l/s) (RPM)
84 21 -10 25 000
84 22 - 11 30 000
85 21 - 10 25 000
84 21 - 10 30 000
82 23 - 11 15 000
82 25 - 12 18 000
82 25 - 12 20 000
82 27 - 13 24 000
82 25 - 12 18 000
82 21 - 10 20 000
82 23 - 11 24 000
79 28,5 -13,5 15 000
80 29,5 - 14 18 000
81 30,3 - 14,3 20 000
81 29,3 - 13,8 18 000
80 29,5 - 14 20 000
Die-grinder
Power
(Hp-W)
0,4 - 300
0,4 - 300
0,4 - 300
0,4 - 300
0,54 - 400
0,54 - 400
0,54 - 400
0,54 - 400
0,54 - 400
0,54 - 400
0,54 - 400
0,67 - 500
0,67 - 500
0,67 - 500
0,67 - 500
0,67 - 500