Pallmann UNO Original Bedienungsanleitung Seite 21

Removing the loose sintered material on new
anhydrite- and magnesia screed
Carbide grinding disc grade 16,
paper grinding disc grade 16
cylindrical brush disc, flat steel brush disc
Finish grinding and levelling
Paper grinding disc grade 40-60,
grinding gauze grade 80-120
Rough grinding and abrading
Paper grinding disc grade 16-24, Carbide grinding disc
grade 24, grinding disc 6 stone
Dismounting and milling of soft or moderately
hard screed and levelling compounds
Carbide grinding disc grade 16, grinding
disc 6 stones, milling disc with star wheel segments,
system carbide milling disc
Grinding extremely hard smoothing compounds and
industrial floors, as well as epoxy coatings
System diamond milling disc
3.7.2 Grinding of parquet and corc
Grinding and abrading timber
Paper grinding disc grade 80
Grinding/polishing parquet + cork
Grinding gauze grade 180
Grinding of parquet varnish, laquer and old surfaces
Grinding gauze grade 60
3.8 Description of grinding, milling and cleaning discs
Paper grinding discs double sided, 375 x 40mm
Grade 16, #013531, Grinding of subfloors
Grade 24, #013527, Preparing and grinding of dirty screeds
Grade 40, #013528, Grinding and levelling smoothing
compounds
Grade 60, #013529, Finish-grinding of smoothing com -
pounds
Grade 80, #013530, Grinding and abrading timber
surfaces
Grinding gauze double sided, 400mm
Grade 60, #013548, Grinding of parquet varnish, coatings
and old surfaces
PALLMANN GmbH l Ein Unternehmen der Uzin Utz AG | Im Kreuz 6 | 97076 Würzburg | Telefon +49 931 27964-0 | Telefax +49 931 27964-50 I www.pallmann.net
Grade 80, #013331, Fine-grinding of surfaces
Grade 100, #013332, Fine-grinding of surfaces
Grade 120, #013333, Fine-grinding of surfaces
Grade 180, #013549, Fine-grinding of surfaces, grinding/
polishing of parquet + cork
Carbide grinding disc
Dismounting action much more aggressive compared to
paper disc. High grinding efficiency. High tool life (10 times
higher as paper grinding discs).
Disc does not clog, due to open grains. Disc can be
cleaned. Silicone or wax-spray can be used additionally to
reduce adhesion.
Grade 16, #013510, Abrading of anhydrite-screed,
removing of dirt and adhesive residues
Grade 24, #013517, For abrading and rough grinding
Cylindrical brush disc, #015735
For preparing new anhydrite- and magnesia-screeds.
For abrading of anhydrite- screed, for abrading areas
contaminated with paint, mortar, felt-, foam- and adhesive
residues.
Corrugated steel-brush disc, #013539
For brushing and preparation of subfloors. For removing
the loose sintered material on new anhydrite- and magne-
sia screed.
Flat steel brush disc #015738
For removal of foam, felt and hessian backing residues.
For abrading anhydrite and self-levelling screeds, for
industrial cleaning. Brush length 45 mm. The open brushes
work well with tacky residues. The brushes do not clog.
Grinding disc with 6 stones K20 #013540
For grinding uneven areas of screed and levelling com-
pounds, paint or gypsum residues. Sharp edges give
high efficiency.
System-milling-disc
The system milling disc can be equipped with different
interchangeable milling modules. The system-discs are
available complete, or, as single modules Use:
System carbide milling disc,
#013569: for removing thick adhesive residues and fibre-,
felt- and foam residues (scraping action)
System diamond milling disc, #020943
for grinding extremely hard smoothing compounds and
industrial floors, as well as epoxy- and polyester coatings
21