Adjusting The Cutting Gear; Troubleshooting; Care And Maintenance - Mantis LH 3000 A Gebrauchsanweisung

• Only insert as much material as will not block up the
feeding tunnel.
• Chop garden waste that has been stored for some
days and is wilted and damp alternately with branch-
es. This will prevent the chopping knife from getting
blocked up.
• Do not fill into the shredder any soft material such as
kitchen waste instead of compositing it.
• Widely branched material with leaves must be com-
pletely chopped before any new material is fed in.
• Take care that the chopped material can freely fall
from the discharge chute – danger of backing up!
• The ventilation slots must not be covered by the
waste bag or the chopped material.

6.5 Adjusting the cutting gear

The anvil blade 2 should be adjusted to have a distance
of 0 to 0,50 mm from the cutting blade 1 (fig. 8). This
distance should be kept to guarantee effective operation
of the mac.
Note! Soft materials or wet twigs can get torn instead of
cut properly due to wrong adjustment. Also a blunt an-
vil blade from frequent use produces the same problem.
On the right hand side of the shredder you will find the
blade adjustment knob (3). To adjust the distance turn the
screw to the right.
1. For lighter material, you can cut through the material
completely turn the knob clockwise half a turn.
2. If you are shredding heavy materials (such as harder
or large materials) they may need to be put through
the shredder twice, to crush the material before cut-
ting it completely. To loosen the adjusting screw, turn
the knob (3) anti-clockwise half a turn.
3. After you have completed the adjustment, check if
the blade cuts efficiently. To avoid and damage to the
shredder make sure that the cutting blade does not
come into contact with the anvil blade.
NOTE!
1. Do not allow garden waste to accumulate before
shredding as it will begin to compost, become too
damp and clog the cutting assembly. Dry material will
help most material to clear the ejection chute. Save
some dry sticks until last to help clean the blade area.
2. Frequently monitor the build up/collection of shredded
material.
3. Do not allow shredded material to build up and fill the
inside of the shredders discharge chute.
4. When the collection box is full, press the On/Off
switch to turn the garden shredder Off before empty-
ing.
WARNING!
Do not put your hands up inside the shredder's discharge
chute to clear away shredded material while the shredder
is switched on or connected to the mains supply.
Electric Garden Shredder Operating Instructions
NOTE! In normal use, do not switch off the garden shred-
der until all of the shredded material has cleared the
cutter assembly. If the garden shredder is switched off
too quickly, remaining pieces of material may clog the
blade assembly and stall the motor when the shredder
is switched back on

7. Troubleshooting

The motor does not run
• The overload protection has responded.
- Set the reversing switch to position REVERSE. The
cutting blade rotates in the reverse direction and re-
lease the material so that you can remove it. Press
the green START button to turn on.
• Power failure
(Fig. 8)
- Check the power supply cord, the plug and your
house connection fuse and RCD.
• Safety switch on the collection box not locked in posi-
tion.
- Ensure collection box is in position and locked.
The material to be chopped is not pulled in
• The chopping knife is running backwards.
- Change the direction of rotation..
• The material is jammed in the feeding tunnel
- Set the reversing switch to position (2). Pull the ma-
terial from the feeding funnel.
- Re-feed thick branches such that the chopping knife
does not immediately grasp the pre-cut notches
again.
The material is clogging up in the feeding funnel
- Pull out the branches from the feeding funnel. Use
the pusher to push or loosen branches inside.
Caution! Change the direction of rotation
to the desired position after the shredder
has come to a complete standstill.

8. Care and maintenance

WARNING!
Before commencing cleaning and maintenance proce-
dures, make sure the garden shredder is switched off and
disconnected from the mains supply. Always wear sturdy
leather gloves when cleaning the cutter blades.
1. To ensure the best performance from the garden
shredder, it must be kept clean.
2. Always clean the garden shredder immediately after
use.
3. Do not allow material to become dry and hard on any
of the garden shredder surfaces. This will directly af-
fect the shredding performance.
4. Make sure that the feeder chute and the ejection
chute are kept clean and clear of all waste material.
5. Make sure that all nuts, bolts and screws are tight and
secure.
GB-6