Package Contents; Operating Instructions; Assembling The Garden Shredder; Collecting Container - Mantis LH 3000 A Gebrauchsanweisung

4. Package Contents

• Remove the packaging material.
• Remove the packaging and/or transportation protec-
tion (if present).
• Verify that the delivery is complete.
• Check the unit and accessories for transportation
damage.
• If possible, store the packaging until the end of the
warranty period. After that period, please dispose of
the packaging in an environmentally friendly manner.
WARNING! The packaging material is not
a play toy! Please keep plastic bags out
of the reach of children. There is a risk
of choking.
1x Silent shredder
2x Wheel set
2x Support foot set
1x Collection box
1x Instruction manual
If parts are missing or damaged, contact your dealer.

5. Operating Instructions

WARNING! You may need help unpacking
and assembling the machine.
After unpacking and inspecting the shredder for damage,
proceed with the following steps:

5.1 Assembling the Garden Shredder

• Turn the shredder over.
• Fold both legs up and insert the supplied axle through
the openings (fig. 2).
• Place both washers on the left and ride side of the
axle (fig. 3).
• Place the supplied threaded spacer on the axle. Then
attach the wheels and finally the safety nuts with the
.
wheel covers
WARNING! Be careful when leaning the
device on the wheels, since the weight is
unbalanced when titled and moved.

5.2 Collecting Container

• Slide the collection box back to the base frame. En-
sure that the collection box runs above the guide rails.
• Lock the collection box with safety switch in position
by pushing upwards

Emptying the collection box

The level of shredded material debris in the collection box
can be checked by looking through the notches on the
GB-5
1x Base frame
1x Small parts bag
1x Adjusting knob
1x Spanner
(Fig. 4)
.
Contact us at www.mantis.uk.com
upper face of the base frame. Always empty the collection
box in good time to prevent it from overfilling.
To empty it, proceed as follows:
a) Switch off the device at the ON/OFF switch.
b) Press the safety switch down
c) Release the collection box. Take the collection box out
at the front.

6. Operation

6.1 On/off switch

(Fig. 5)
• Press the green button (1) to switch on the shredder.
• Press the red button (2) to switch it off
Note! This machine is equipped with an
electromagnetic switch to prevent it from
being unexpectedly switched on when
power source recovered.

6.2 Reversing switch

This shredder has an automatic overload
protection and reverse switch.
A sudden blocking the device automatically (3 sec.) can
change the direction of rotation. The material is trans-
ported back (5 sec.). To prevent damage to the engine,
the circuit breaker (1) the power supply is automatically
turned off.
If the cutting blade still jammed after 5 seconds, so that
the motor can no longer run, press the rotational direc-
tion switch REVERSE (2). The cutting blade rotates in
the reverse direction and release the material so that you
can remove it. Press the green START button (3) to turn
on the chopper.
6.3 Disassembling
For certain purposes, e.g. storage after use, etc, you can
disassemble the shredder in the reverse order as de-
scribed under "Assembling ".
6.4 Operating Instructions
Feeding
Feed the material to be chopped into the right side of the
feeding tunnel. The material is automatically pulled in by
the chopping knife.
Caution! Longer material standing out
from the machine could lash out when
being pulled in by the chopping knife!
Keep a safety distance!
Warning! Always use the pusher (Fig.11)
if you try to push the material into the
feeding tunnel. Do not use your hands
directly! Keep the pusher well after use.
(fig. 4).
(Fig. 6)