Specifications - IMG STAGELINE TXS-855 Bedienungsanleitung

Activating the lock
1) Keep the button SET (6) pressed until the letter
"G" starts flashing on the display; the group
setting mode is activated .
2) Press the button SET repeatedly until the dis-
play shows
flashing .
3) To activate the lock, press the button
display shows
4) Press the button SET to confirm . The display
briefly shows
the normal mode .
The indication LOCK (e) on the display
shows that the lock has been activated . When
you press a button or when you set the on /off
switch (8) to OFF,
Deactivating the lock
1) Make sure that the on /off switch (8) is set to ON .
2) Keep the button SET (6) pressed until the indi-
cation LOCK (e) starts flashing on the display .
3) To deactivate the lock, press the button
The display shows
4) Press the button SET to confirm . The display
briefly shows
normal mode .
5.2 Automatic frequency matching
(REMOSET function)
Via a 2 .4 GHz radio signal of the receiver, the trans-
mitter is matched to the transmission frequency of
the receiver . The range of REMOSET transmission
may reach up to 10 m . Transmission is not possible
when the receiver is locked (deactivating the lock
☞ chapter 5 .1 .4) .
After setting the desired transmission frequency
on the receiver ( ☞ chapter 5 .1 .1) and switching
on the transmitter, press the button REMOSET (3) .
When the REMOSET function has been activated,
the luminous ring of the button starts flashing
rapidly . The display briefly shows the identifica-
tion number of the receiver (
After matching the frequency, the transmitter is
set to the channel group and the channel of the
receiver . The luminous ring of the button lights
permanently again .
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
(lock off) and LOCK (e) starts
.
. The receiver will return to
appears in addition .
.
. The unit will return to the
☞ chapter 5 .1 .3) .
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
If the luminous ring keeps flashing after the REMO-
SET function has been activated, the receiver does
not receive a radio signal from the transmitter on
the transmission frequency adjusted, e . g . when
REMOSET transmission has failed (troubleshooting
☞ box below) or when the transmitter is muted at
the time of REMOSET transmission .
(7) . The If the transmitter has not been set to the channel group
and the channel of the receiver, check the following
adjustments on the transmitter:
 Has the lock function been activated on the trans-
mitter?
 Has the automatic frequency matching been disabled
on the transmitter?
 Does the identification number set on the transmitter
differ from the one set on the receiver?
Correct the corresponding setting on the transmitter
and press the button REMOSET once again .

6 Specifications

Carrier frequency range: . 506 – 542 MHz
(5) .
REMOSET transmission: . . 2 .4 GHz
Audio frequency range: . 40 – 18 000 Hz
THD: . . . . . . . . . . . . . . . . < 0 .6 %
Dynamic range: . . . . . . . . > 105 dB
Squelch: . . . . . . . . . . . . . pilot tone / noise mute
Audio outputs, bal .: . . . . 100 mV,
Ambient temperature: . . 0 – 40 °C
Power supply: . . . . . . . . . via power supply unit
Dimensions W × H × D
(w /o antennas): . . . . . . . . 210 × 42 × 195 mm
Weight: . . . . . . . . . . . . . 525 g
Subject to technical modification .
☞ table on page 24
XLR (with 20 dB at-
tenuation switch) and
6 .3 mm jack
provided and connected
to 230 V/ 50 Hz
13