ECX Temper ECX00012T1 Bedienungsanleitung

®
ECX00012T1/T2 | 1:24 4WD ROCK CRAWLER RTR
EN
Notice
All instructions, warranties and other collateral documents are subject to change at the sole
discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com
and click on the support tab for this product.
Meaning of Safety Signal Words
The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:
NOTICE: Instructions, which if not followed, create a possibility of property damage AND minor
injury.
CAUTION: Instructions, which if not followed, create the probability of property damage AND a
possibility of injury.
CAUTION: Read and follow all instructions and warnings in the manual prior to setup or use.
Failure to operate the product correctly can result in damage to the product, personal property
and/or injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and
requires some basic mechanical ability. Do not attempt disassembly, use with incompatible
components or augment the product in any way without the approval of Horizon Hobby, LLC.
Age Recommendation: Not for children under 14 years. This is not a toy.
Operating Safety Precautions
»
As the user of this product, you are responsible for operating it safely, not
endangering yourself and others, or damaging the product or the property of others.
»
Operate your product in open spaces away from people and property.
»
Never operate your product with damaged electrical components.
»
Keep the transmitter powered on while model is powered on.
»
Let parts cool before touching, motors will get hot during use.
»
Remove batteries after use, if removable.
CAUTION: Failure to exercise caution while using this product and complying with
the following precautions could result in product malfunction and/or void the warranty.
Charging Warnings
WARNING: Failure to comply with the following warnings could result in product
malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property
damage.
»
NEVER LEAVE CHARGING BATTERIES UNATTENDED OR CHARGE OVERNIGHT.
»
Never charge damaged batteries. If the battery begins to swell during charging or use,
discontinue immediately.
»
Always use the included battery and charger. Disconnect the battery after charging.
»
Charge batteries away from flammable materials in a well-ventelated area.
»
Never charge, transport, or store batteries in hot, cold, or very sunny places
(recommended between 40–120° F or 5–49° C).
COMPONENTS
Body
Temper™ 1:24 4WD Rock Crawler: RTR
Operating Weight
0.20kg (0.4 lb.)
Transmitter
2 CH (4AA batteries)
Charger
USB
Battery
1/3AAA, 150mAh, 4.8V
Motor
Micro
ESC/Receiver
2 in 1 receiver/speed control
1
Charge the Vehicle Battery
1. Connect the battery to the battery charger.
2. Connect the battery charger to a powered USB.
3. The battery will charge in under 2 hours.
The LED sequence for the USB charger is Red = charging, Green = charge is complete.
2
Remove the body from the
vehicle
3
Install the vehicle battery
4
Transmitter Controls
REVERSE SWITCH
Allows you to change the direction of
steering (ST. REV) and throttle (TH. REV)
controls (Ensure proper function with a
radio system test).
THROTTLE DUAL RATE
Adjusts the maximum
amount of throttle the
vehicle can be given
STEERING DUAL RATE
Adjusts the total
steering travel
POWER SWITCH
Power on or off the transmitter
5
Installing Your Transmitter Battery
This transmitter requires 4 AA batteries.
1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable
batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to national regulations.
6
Binding
Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter. The included transmitter and receiver are bound at the factory. If you need to rebind,
follow the instructions below.
1. Power off the transmitter and ESC.
2. Connect a fully charged battery pack to the ESC.
3. Press and hold the bind button while powering up the ESC. After 2 seconds the ESC will be in bind mode.
4. Release the bind button and power on transmitter. Binding is complete.
You must rebind when binding the receiver to a different transmitter.
TIP: Use the body pin that came with your vehicle to press the bind button within its waterpoof cover.
NOTICE: Do not attempt to bind the transmitter and receiver if there are other compatible transmitters in bind
mode within 400 feet. Doing so may result in unexpected binding.
OWNER'S MANUAL
7
8
BATTERY LEVEL INDICATOR
Solid Red and Green:
Battery voltage is
good (above 4V).
9
Solid Red: Battery
voltage is critically low
(below 4V). Replace
transmitter batteries.
THROTTLE TRIM
Adjusts the neutral
point of the electronic
speed control
STEERING TRIM
Adjust to make
the vehicle drive
straight with
no input at the
10
steering wheel
1. Do a test of the transmitter's control of the vehicle
with the vehicle's wheels off the ground.
2. Start driving slowly, and, and, if the vehicle does
not go straight, adjust the steering trim dial on the
transmitter.
STEERING WHEEL
Control steering.
Right and Left
steering
When You Are Finished
THROTTLE TRIGGER
Controls power
to the motor
for forward
or reverse
11
Reverse
Stop
Forward
12
13
BIND
ON OFF BATT MOTOR
Re-install the body
on the vehicle
Power on the
transmitter
Power on the
vehicle
Control Test
Power off the
vehicle
Power off the
transmitter
Remove and
recharge the
vehicle battery