Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ULTRASOUND
WARNING
EC-DECLARATION OF
COMPLIANCE
• Never under any circumstances
attempt to open or inspect the internal
This product meets the following
components or accessories of the
requirements:
machine. If an inspection becomes
1.
necessary, please contact your supplier
Conditions set out in the Low Voltage
or a suitably competent technician.
Directive: 2006/95/EC
2.
• Never use the unit in humid or poorly
Conditions set out in the
ventilated environments, such as wet
Electromagnetic Compatibility Directive:
rooms, bathrooms etc. to prevent damage
2004/108/EC
to the electrical components of your unit.
• Never use the unit outdoors; exposure to
RECYCLING
the elements can cause damage.
• If the power cord was destroyed, please
ask a professional to service and replace
packaging bear this symbol, it means
it to avoid hazards, or contact the dealer
that these products should not be treated
for service.
as conventional household waste in
Europe. To ensure proper treatment of this
• Do not leave any ultrasound probes
waste, dispose of it in accordance with
switched on whilst unattended, otherwise
local laws or as required for the disposal
they may overheat, which could result in
of electrical equipment. This initiative will
damage to the probe or a reduction of its
help preserve save natural resources and
service life.
improve standards of environmental
protection in regard to the treatment of
• Do not attempt to separate the stainless-
electrical waste.
steel generator from its rubber holder
(handle); any attempt to do so may cause
irreparable damage to the generator.
WELCOME!
Thank you very much for purchase.
Please read the instructions carefully
before operating the instrument. You can
also ask a professional for guidance to
make sure you are using the instrument
correctly. We will accept no responsibility
for any accidents that occur due to
incorrect operation.
The company reserves the right to amend
the details of the instruments with no prior
notice. If any mistakes are found in these
EN
instructions, please feel free to send us an
e-mail informing us so that we can correct
F-312A
them.
Instruction Manual
WE-2013-F312A-1
PACKAGE CONTENTS
• These components are subject to
change without prior notice.
• Appearance of product may differ from
the image.
No.
PRODUCT
1
EYE PROBE
2
FACE PROBE
3
MAIN UNIT
4
FEEDER CABLE
FRONT PANEL
Whenever any of our electrical
products or their presentation
INSTRUCTIONS OF USE
BEFORE TREATMENT:
1.
Cleanse/tone the treatment area using
the prescribed skin-type products.
2.
Remove any left-over product by facial
steam for 10 minutes.
3.
Cleanse the treatment area again to
remove any dirt or debris from the face in
order to prevent the ultrasound waves from
pushing it back into the dermis.
4.
Tone every part of the face (or treatment
area) gently using a suitable astringent.
5.
After wiping off the astringent, the skin
will be thoroughly cleansed for optimum
protection.
6.
Apply enough conductive gel to the
treatment area.
STARTING TREATMENT:
1.
Connect the power supply via the rear
panel.
2.
Connect the accessories properly in the
lateral panel.
3.
Turn on the "POWER" button.
4.
Adjust the intensity of the output
REF.
QTY.
according to the "ENERGY" blocks on the
10034
1
LCD display. Generally, you should start at
10035
1
-
1
3-4 blocks and then increase as required.
-
1
5.
Select the desired wave state by
switching the "STATE" button. There are
3 kinds of wave state: continuous wave,
intermittent wave, and combined wave.
6.
Select the desired output probe (face or
eyes) by pressing "SELECT".
7.
Hold the ultrasonic probe firmly and
press the "START/PAUSE" button to begin.
8.
Massage the treatment area where the
conductive gel has been applied using
small circular motions to cover the whole
treatment area. Treatment time will vary
depending on the size of treatment area.
A standard (complete) facial area should
take 10-15 minutes of repetitive massage.
9.
After completing the treatment, switch
off the output and return the probe to its
holder.
NOTES
• Always make sure enough conductive
gel is applied for at least 15 minutes of
treatment time.
• Generally, lower outputs are used
for facials and higher outputs for body
treatments.
• If the treatment area is small or sensitive,
use the eye probe and make sure that the
energy output is limited to 5-7 blocks (on
the "ENERGY" LCD screen display). The
treatment time may also be reduced to
8-10 minutes.
• A standard treatment course lasts
around 10 sessions in total, with a
minimum resting period of 1 day between
sessions. If other facial treatments are
being conducted on the same area, a
minimum rest period of 7 days should be
observed between treatments.
CAUTIONS
• Never use on dry skin.
• Do not use on the stomach area of
pregnant women.
• Do not use on people with pace-makers
(any electrical or rhythmic heart-regulating
device).
• Do not use on people with known heart
MAINTENANCE
conditions.
• Always use ultrasonic electrodes with
• The ultrasound probes should be
enough moisturizer or serum on the skin.
cleaned using clean water (not hot) and
a clean, soft cloth and then chemically
• Ultrasonic treatment is suitable for
sterilized using an appropriate sterilization
all skin types. The massage time and
fluid. Dry the probe carefully after
machine settings can be adjusted for
sterilizing and store it safely in its holder
each different skin type. For sensitive
on the trolley in between uses. Always
skins, reduce treatment time to 3-5
sterilize the probes again prior to use.
minutes and make sure the power setting
is at the lowest level to start with.
• Never immerse the probe in any fluid!
ACCESSORIES
FAQ
REF.
Check the following if the work unit
10034
switches on but the probes do not emit.
10035
• Put a drop of water on one probe.
• Switch on the unit and slowly increase
the output energy.
• If the water starts to move and
evaporate, the unit and the probes are
working properly. If not, the probes are
not working properly.
The unit and the probes are working
properly but the customer doesn't feel any
effects.
• Make sure enough conductive gel has
been applied to the treatment area.
TECHNICAL SHEET
Weights and sizes
Packing size (cm)
Gross weight (kg)
Product size (cm)
Working characteristics
Working power
Working frecuency
Preset working time
Electrical characteristics
Rated voltage
Frecuency
Rated power
Visit our website at www.weelko.com for more information
DESCRIPTION
EYES PROBE
FACE PROBE
37x27,5x14
3,5
20,7x22x7
0 - 3 W/cm2
1 MHz
15 min
220V ~ 240V
50Hz/60Hz
20 W
© 2013 Weelko
Werbung
