Si encuentra algún error en estas instrucciones, por favor no dude en enviarnos un e-mail para informarnos y que podamos corregirlos. Importador/Importer Importateur/Importeur Importatore: Weelko Barcelona, S.L. ESB65397556 Barcelona Pol. Ind. La Valldan Camí de Garreta, 92 08600 Berga Barcelona – Spain T.
Panel frontal Energy Timer F-336A Start/Pause Microcrystal Instrucciones de uso 1. Conecte el cable de alimentación en el panel trasero. 2. Encender el instrumento mediante el botón “POWER”. 3. Pulse la tecla “FUNCTION” para seleccionar la función deseada en el siguiente orden: microdermoabrasión con microcristales, microdermoabrasión con puntas de diamante.
Seite 4
4. Ajustar la potencia y el tiempo de trabajo mediante MICRODERMOABRASIÓN CON los botones “ENERGY” y “TIMER” respectivamente. La MICROCRISTALES potencia de salida por defecto es 1 (ajustable de 1 a 10) y el tiempo de trabajo predeterminado son 15 Instrucciones de uso minutos (ajustable de 0 a 60 minutos) 5.
MANTENIMIENTO • Si el dispositivo produce un ruido anormal: El filtro en el recipiente nº 1 impide que los micro cristales penetren en el circuito de succión del equipo. • Retirar los 4 tornillos que se indican a continuación. Se entregan 4 filtros de recambio. Para sustituir dicho Estos tornillos tienen la finalidad de sujetar la bomba filtro desenroscar el soporte del tapón del recipiente, durante el transporte del equipo.
Seite 6
MultiEquipment. Ref F336A Instruction manual Micro-crystal dermabrasion...
Seite 7
Importador/Importer Importateur/Importeur Importatore: Weelko Barcelona, S.L. ESB65397556 Barcelona Pol. Ind. La Valldan Camí de Garreta, 92 08600 Berga Barcelona – Spain T.
Front panel Energy Timer F-336A Start/Pause Microcrystal Instructions of use 1. Connect the power supply via the rear panel. 2. Turn on the “POWER” button. 3. Press “FUNCTION” to select the desired function in the following order: micro-crystal dermabrasion, diamond dermabrasion. Micro-crystal containers: 1.
Seite 9
4. Select the desire power output and time of working MICRO-CRYSTAL DERMABRASION by pressing “ENERGY” and “TIMER” respectively. “ENERGY” can be adjusted between 1 and 10. “TIMER” Instructions of use can be adjusted between 1 and 60 minutes. 1. Assembly the plastic handle holder in on side of the 5.
MAINTENANCE • If the device produces an abnormal sound: The filter in container #1 prevents micro crystals entering the suction circuit of the equipment. 4 • Remove the 4 screws indicated below. These screws replacement filters are delivered. To replace the filter, are intended to fasten the pump during transport of unscrew the cap of the container stand, remove the the equipment.
Seite 11
MultiEquipment. Ref F336A Mode d’emploi Microdermabrasion avec des microcristaux en aluminium...
Si vous détectez une erreur dans ces instructions, n’hésitez pas à nous le faire savoir afin d’y apporter une solution. Importador/Importer Importateur/Importeur Importatore: Weelko Barcelona, S.L. ESB65397556 Barcelona Pol. Ind. La Valldan Camí de Garreta, 92 08600 Berga Barcelona –...
Panneau avant Energy Timer F-336A Start/Pause Microcrystal Mode d’emploi 1. Branchez le cordon d'alimentation arrière du panneau. 2. Allumez l'appareil en appuyant sur "POWER". 3. Appuyez sur "SELECT" pour sélectionner la fonction désirée. Récipients pour les microcristaux: 1. Récipient pour les microcristaux utilisés. 2.
Seite 14
4. Bien fermer la bouteille. La zone de filetage du MICRODERMABRASION PAR bouchon doit rester complètement propre de MICROCRISTAUX EN ALUMINIUM microcristaux. Il faudrait utiliser microcristaux de taille de particule #120. Mode d’emploi Note importante: ne manipuler pas les microcristaux avec les mains.
Seite 15
MAINTENANCE • Si la pompe fait un bruit inhabituel: Ne pas utiliser l'appareil si le tuyau filtrant relié à l'appareil n'est pas installé. Ce filtre doit être • Enlever les 4 vis de fixation de la pompe au fond de remplacé...
Seite 16
MultiEquipment. Ref F336A Bedienungsanleitung Mikrokristallen Microdermabrasionsgerät...
Seite 18
SCHALTTAFEL Energy Timer F-336A Start/Pause Microcrystal Gebrauchs 1. Stecken Sie das Stromkabel an der Geräterückseite ein. 2. Drücken Sie die Taste “POWER“ 3. Drücken Sie die Taste “SELECT” um die gewünschte Funktion zu wählen. Folgende Reihenfolge ist einzuhalten: Mikrodermabrasion mit Mikrokristallen aus Aluminium und Mikrodermabrasion mit Diamant-aufsätzen.
4. Stellen Sie die Ausgangsleistung mit “ENERGY” auf MIKROKRISTALLEN den gewünschten Pegel ein (von 1 bis 10). Wählen Sie MICRODERMABRASIONSGERÄT die Dauer der Behandlung mit der Taste „TIMER“ (Standard 15 Minuten aber von 0 auf 60 Minuten Gebrauchs einstellbar). 5. Drücken Sie “START/PAUSE” um mit der 1.
WARTUNG • Sollte die Ansaugpumpe ungewöhnliche Geräusche Dieser Filter muss nach jeweils 5 Behandlungen machen: ausgetauscht werden. • • Entfernen Sie die 4 Schrauben, mit denen die Pumpe Filterwechsel: am unteren Bereich des Gerätes befestigt ist. Diese - Schrauben Sie den oberen Bereich des Tanks auf. Schrauben fixieren die Pumpe, damit sie während des Transports nicht beschädigt wird.
Seite 21
MultiEquipment. Ref F336A Manuale d’istruzioni Microdermoabrasione con microcristalli...
L'Azienda declina ogni magnetica: 2014/30/EU responsabilità derivante da eventuali incidenti dovuti a un utilizzo non corretto dell’apparecchio. Importador/Importer Importateur/Importeur Importatore: Weelko Barcelona, S.L. ESB65397556 Barcelona Pol. Ind. La Valldan Camí de Garreta, 92 08600 Berga Barcelona – Spain T.
Panello frontale Energy Timer F-336A Start/Pause Microcrystal ISTRUZIONI D’USO 1.Connettere il cavo d’alimentazione nel pannello posteriore. 2. Accendere l’apparecchiatura tramite il tasto “POWER”. 3. Montare il supporto porta-recipienti di plastica nel laterale dell’unità principale. 4.Collegare correttamente i tubi applicando una leggera pressione, come indicato nello schema sottostante.
Seite 24
MICRODERMOABRASIONE CON 4. Regolare la potenza e la durata del trattamento tramite i tasti '"ENERGY" e "TIMER", rispettivamente. MICRO CRISTALLI La potenza d’uscita per difetto è 1 (regolabile 1-10) e la durata del trattamento predefinita è di 15 minuti Istruzioni d’uso (regolabile da 0-60 minuti).
Seite 25
MANTENIMIENTO • Se il dispositivo produce un suono anomalo: Il filtro nel contenitore nº. 1 impedisce che i micro cristalli penetrino nel circuito di aspirazione • Rimuovere le 4 viti di seguito illustrate. Tali viti dell’apparecchio. Vengono consegnati quattro filtri di servono a fissare la pompa durante il trasporto ricambio.