Peltor Lite-Com Basic Gebrauchsanweisung Seite 21

PELTOR Lite-Com Basic
Wireless communication headset
The Peltor Lite-Com Basic offers reliable, efficient wireless communication between
two or more people, even in noisy environments. Read these instructions carefully
to ensure the best possible benefit from your Peltor product.
PROPERTIES
• Wireless communication headset with 8 channels. High power gives a range of
up to 2 km outdoors. Low power gives a range of up to 1 km.
• 38 subchannels, allowing multiple users to use the same channel without interfer-
ing with each other.
• Operating time 10–35 hours, depending on the type of battery and mode of use.
• Warning every other minute when battery is low.
• Automatic shut-off 2 hours after the last activation.
• Selected settings are confirmed with a voice message or a tone. The last setting
is stored when the unit is switched off.
ADVANTAGES (Fig. H)
1. Extra broad headband (MT53H7A4400) with soft padding for ideal com-
fort throughout the working day. Specially designed helmet attachments
(MT53H7P3E4400) with slots for attaching a visor and rain shield.
2. Individually sprung headband wires of stainless steel provide an even distribu-
tion of pressure around the ears. Steel headband wires maintain their resilience
better than regular plastic headbands through a wide range of temperatures.
3. Low, two-point fasteners and easy height adjustment with no protruding
parts.
4. Soft, wide foam/fluid-filled ear cushions with built-in pressure-relief canals
for low pressure, effective sealing and individual comfort.
5. Flexible antenna with low attachment and high receptivity.
6. Connector for external equipment, such as another communication radio, mobile
telephone, Walkman etc.
7. Battery cover for easy battery replacement. (Two 1.5-volt AA alkaline batteries
included. Peltor's ACK03 accumulator battery or other rechargeable AA batteries
can also be used).
8. Ambient-noise compensated speech microphone for high speech recognition
with Quick Positioning for easy configuration.
9. Keypad for easy regulation of Lite-Com Basic functions.
PUSH-BUTTONS (Fig. A)
1. ON/OFF/MODE (O)
2. UP (+)
DOWN (–)
3. PTT
INSTRUCTIONS FOR USE/SETTINGS
ON/OFF/MODE
Switch the Lite-Com Basic on and off by pressing and holding the ON/OFF/MODE but-
ton for about 2 seconds. A tone confirms that the unit has been switched on or off.
Press ON/OFF/MODE (O) briefly to move through the menu. Press the button slowly,
one step at a time, and each step is confirmed with a voice message. More rapid
key presses only confirm the last function mentioned.
Current settings are stored when the unit is switched off.
VOLUME
Use the UP (+) and DOWN (–) buttons to set the incoming volume in the communica-
tion radio. A voice message confirms the new setting each time you press the button.
There are five volume steps and an off mode. To access off mode, press and hold
the DOWN (–) button for one second. A voice message confirms "volume off".
Note: No radio communication is audible in off mode.
To switch the radio back on, press the UP (+) button. You start receiving on the
lowest volume level.
CHANNEL
Use the UP (+) and DOWN (–) buttons to select a channel (radio frequency) for
the communication radio. A voice message confirms the new setting each time you
press the button. You can choose from eight channels with frequencies around 446
MHz (see fig. L).
VOX (Voice-controlled transmission)
VOX means that the Lite-Com transmits when sounds of a certain volume reach
the microphone –hands-free transmission. The Lite-Com Basic also has AntiVOX,
which means that voice-controlled transmission is not possible if the channel is
already in use. This prevents interference.
Use the UP (+) and DOWN (–) buttons to set the sensitivity for voice-controlled
transmission. A voice message confirms the new setting each time you press the
button. There are five VOX levels and an off mode. To access off mode, press and
hold the DOWN (–) button for one second. A voice message confirms "VOX off".
18
Switches the Lite-Com Basic on and off, and lets
you choose between alternatives in the menu.
Increases the level of the selected function.
Decreases the level of the selected function.
Transmits with the Lite-Com Basic.