Remote Control; Inserting Batteries; Flight Control - REVELL Control TURACO Anleitung

2 reMOTe CONTrOl

2A Left/right trim 2F Up/Down thrust
buttons control
2B Infrared trans- 2G Charge cable
mitter compartment
2C ON/OFF switch 2H Fly left/right
2D Channel selector 2I Charge LED
switch
2E Power LED
4 ChargINg The helICOPTer
Attention: The battery must cool down for 10 to 15 minutes before charging and
after every flight. Failure to do so may result in the battery becoming damaged.
The charging process is electronically monitored, but do not leave it unsupervised.
• Switch off the helicopter and the remote control.
• Carefully pull open (4A) the charge cable compartment (2G).
• Carefully insert the charging cable in the charge socket of the helicopter (4B).
The plug must be gently inserted into the charging socket – DO NOT USE
FORCE. If the plug is not correctly inserted into the charging socket, the
helicopter can be damaged and there is a risk of injury under certain circumstances.
• Switch on the remote control, the Power LED (2E) illuminates red and the charge
LED (2I) illuminates green.
• The charging process has been completed when the charge LED goes out.
• After the charging process, switch the power switch to "OFF" and disconnect
the charge cable from the helicopter.
After a charge time of approx. 35 minutes with the USB charge cable the
helicopter can fly for approx. 6-8 minutes.
You can also charge your helicopter with the accompanying USB cable:
• Switch off the helicopter.
• Insert the USB plug in an open USB port (2C).
• Carefully insert the charging cable in the charge socket of the helicopter (4D).
The plug must be gently inserted into the charging socket – DO NOT USE
FORCE. If the plug is not correctly inserted into the charging socket, the
helicopter may become damaged and, under certain circumstances,
become an injury risk.
• The charging process has been completed when the USB plug lights up.
• After the charging process has been completed, disconnect the USB plug
from the USB port and from the helicopter (4E).
5 STarT PreParaTION
The thrust controller (the left controller on the remote control) must point down before
being switched on (5A). Then set the remote control's control ON/OFF switch to "ON"
(5B). The Power LED illuminates red . Select the channel A, B or C with the channel
selector. Now set the ON/OFF switch on the right side of the helicopter to the "ON"
position (5C). Place the helicopter on the ground so that its tail points toward you
(5D). The LEDs on the helicopter begin to blink. After approximately 3 seconds the
helicopter is ready to start.
14

3 INSerTINg BaTTerIeS

(reMOTe CONTrOl)
3A Unscrew and remove the cover.
3B Insert 6 x 1.5 V AA batteries and
pay attention to the polarity, as
shown in the battery compartment.
3C Close the battery cover and secure
with the screw.
6 TrIM aDJUSTMeNT OF The CONTrOl
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
6A
If the helicopter automatically
rotates clockwise...
If the helicopter begins to automati-
cally rotate clockwise quickly or slowly,
briefly tap the anti-clockwise counter-
rotation trim adjustment until the heli-
copter no longer rotates automatically.
Do not simply actuate the trim buttons
continuously.

7 FlIghT CONTrOl

Note: Your helicopter is to fly forwards.
7A In order to start or gain altitude,
carefully move the thrust control
forward.
7C To fly along a left-handed curve,
carefully move the directional controller
to the left, as long as the helicopter
tail is facing toward the pilot.
FlyINg MUlTIPle helICOPTerS SIMUlTaNeOUSly
Up to three pilots can fly their helicopters simultaneously! To do so, proceed as follows:
• Pilot 1 switches his/her remote control on and selects channel A.
• Pilot 1 switches on his/her helicopter. After approximately 3 seconds the helicopter
is set to channel A.
• Pilot 1 sets his/her remote control aside without switching off the remote control
or helicopter.
• Pilot 2 switches his/her remote control on and selects channel B.
• Pilot 2 switches on his/her helicopter. After approximately 3 seconds the helicopter
is set to channel B.
• Pilot 2 sets his/her remote control aside without switching it or the helicopter off.
• Pilot 3 switches his/her remote control on and selects channel C.
• Pilot 3 switches on his/her helicopter. After approximately 3 seconds the helicopter
is set to channel C.
They can now be flown at the same time!
6B
If the helicopter automatically
rotates anti-clockwise ...
If the helicopter begins to automa-
tically rotate anti-clockwise quickly
or slowly, briefly tap the clockwise
counter-rotation trim adjustment until
the helicopter no longer rotates auto-
matically. Do not simply actuate the
trim buttons continuously.
7B Move the thrust control back
for landing or to fly lower. Only
minimal corrections to the controller
are necessary to ensure smoothing
flying of the helicopter!
7D To fly along a right-handed curve,
carefully move the directional controller
to the right, as long as the helicopter
tail is facing toward the pilot.
15