cam CULLAMI Gebrauchsanweisungen Seite 16

Cullami 31 gennaio 2018 conv_Layout 1 31/01/18 14:28 Pagina 16
INSTRUCTIONS FOR USE
EN
tube of the rear arch.
13 Insert the hard partition in the pocket created in
the fabric immediately under the dropside.
14 Close the zip to secure the fabric in the rear part of
the cradle, around the tube of the rear arch.
15 Fit one of the two parts of the fastening system in
the tube of the dropside of the cradle. Secure it with a
screw.
16 Insert the tube of the dropside inside the pocket
created in the part of the fabric that can be opened.
17 Insert the other part of the fastening system in the
tube of the dropside of the cradle. Secure it with a
screw.
18 Close the dropside, securing it to the frame as
shown in the diagram. A "clack" sound will show that
it has been fastened correctly.
19 Close the zip. Repeat the operation on both sides.
20 Insert the wooden base in the pocket of the
mattress. The position of the holes on the wooden
board must match that of the buttonhole made in the
fabric covering the mattress.
21 Screw the buckles to the wooden base. Repeat the
operation on both sides.
22 Insert the mattress in the cradle. The position of
the buckles must match that of the buttonhole made
in the fabric of the cradle base.
23 Pull the buckles through the buttonhole in the
fabric of cradle base. Repeat the operation on both
sides.
24 Assemble the support rod as shown in the diagram.
25 Insert the mobile bar on the support as shown in
the diagram; the bar must be turned towards the
outside of the cradle.
26 Rotate the bar towards the centre of the cradle to
lock it in place.
27 Rotate the bar towards the outside and pull it
upwards to release it.
28 Press the brake to lock the castors. Lift the brake to
release the castors.
29 To raise the cradle, pull it upwards on both sides.
A "clack" sound will show that it has been fastened in
the required position.
30 To lower the cradle, press the button located on
the side of the joint and lower the cradle to the
required position. A "clack" sound will show that it
has been fastened in the required position. Repeat the
operation on both sides.
31 The cradle can be inclined by adjusting the height
to two different positions. Warning: the cradle can be
inclined, but with a maximum difference in the angle
of 3 positions.
32 Position the baby's head on the highest side. Do
not position baby's head on the lowest side.
33 Use the rocking function keeping the cradle in the
middle of the frame. Do not leave the cradle in the
rocking position when baby is left in the cradle
unattended. Always block the cradle. Use the rocking
function keeping the cradle in a horizontal position;
do not use it when the cradle is in an inclined position.
34 To rock the cradle, press the release button located
on the front of the main joint. Repeat the operation on
both sides.
35 To block the rocking action, press the locking
button on the side of the main joint. Repeat the
operation on both sides.
Bedside mode (securing to an adult bed).
36 Open the zip at the sides of the dropside of the
cradle.
37 Press the button to release the dropside and lift to
release. Repeat the operation on both sides.
38 In the bedside mode, the cradle must be positioned
so that there is never any space between the lower
side of the cradle and the mattress of the adult bed. If
necessary, the cradle can be moved sideways to bring
15
it closer to the mattress of the adult bed. To move the
cradle sideways and adjust the distance from the adult
bed, press the button located on the main joint and at
the same time adjust the cradle in the required
position. A "clack" sound will show that the cradle has
been fastened in the required position. Repeat the
operation on both sides. The cradle must be moved
sideways in the same way on both sides.
39 Line the cradle up with the adult bed.
40 Adjust the height of the cradle compared with the
adult bed. The top of the side must be at least 1 cm.
lower than the height of the mattress of the adult bed.
41 Fasten the belts to the buckle located under the
cradle. Repeat the operation on both sides.
42 Pass the belts around the frame of the adult bed
from the bottom upwards. Repeat the operation on
both sides.
43 Fasten the buckle so that a loop is formed. Repeat
the operation on both sides.
44 Move the cradle as close as possible to the adult
bed and pull the belts hard. Repeat the operation on
both sides.
Accessories
45 Mosquito net: insert the mosquito net on the
mobile support rod, as shown in the diagram.
46 Pull the metal ring outwards to open the mobile
fastening system. Hook the mobile to the support.
Release the metal ring to secure the mobile. Check
before use that the mobile fastening system is
inserted correctly.
47 To assemble the mobile, follow the steps shown in
the diagram.
Maintenance
To clean the cradle use warm water and soap. Do not
use solvents or derivatives. Dry the metal parts to
prevent the formation of rust. Wash the cover by hand
in warm water (max. 30° C) using low-duty detergents
for delicate fabrics. Do not bleach. Do not use driers,
do not dry clean, do not iron. Dry flat in the shade.
Spare parts
1 – 925/1 – Rear ring tube
2 – 925/2 – Blind stopper
3 – 925/3 – Complete joint
4 – 925/4 – Dropside fastening system with male
connector
5 – 925/5 – Dropside fastening system with female
connector
6 – 925/6 – Front tube
7 – 925/7 – Main tube with feet couplings
8 – 925/8 – Foot
9 – 925/9 – Castor with brake
10 – 925/10 – Foot tube
11 – 925/11 – Button
12 – 925/12 – Plate with Cam logo
13 – 925/13 – Mobile bar plug (optional)
14 – 925/14 – Complete mobile bar (optional)
15 – 925/15 – Mobile bar pin
16 – 925/16 – Mobile bar tip
17 – 925/17 – Hard partition
18 – 925/18 – External cradle fabric
19 – 925/19 – Wooden mattress base
20 – 925/20 – Mattress
21 – 925/21 – Mattress cover
22 – 925/22 – Mobile (optional)
23 – 925/23 – Belts for fastening to bed (2 pieces)
24 – 925/24 – Instruction manual
25 – 925/25 – Mosquito net (optional)
26 – 925/26 – Bedding set pillowcases and sheets
(optional)