pixima fontanot CUBE TUBE PVC Montageanleitung Seite 7

21. Tighten element C70 permanently (fig. 8).
22. Tighten tread element B02 in a permanent manner. Assemble elements C72 on the treads (L30) (determine
the position of the openings using the template provided) with articles C57 and B02 and drill using a Ø 4.5 mm
point (fig. 2).
23. Check the verticality of the balusters (C67) again and correct by repeating the operations described above, if
necessary.
24. Position the first baluster (C67). Adjust the height of a long baluster (C67) cutting the end to the same height as
those already assembled (fig. 1).
25. Fasten element F34 to the floor near the first baluster (C67), drill using a Ø 8 mm point. Use elements C58,
B12, B83 and B02. (fig. 1).
26. Start from the baluster (C67) on the landing (E02) and begin by securing the handrail (A14).
Use elements C64 with the screwer. Warning: position the seam of the coating on the handrail toward the
bottom.
27. Join the other segments of the handrail (A14) tightening and gluing them one after the other with articles B33.
Cut the handrail (A14) near the corner treads and use the corner joints A15, articles C64 and the glue X01.
For a homogeneous handrail, curve the final part of the handrail until it joins with the last part of the previous
handrail (fig. 9).
28. Saw off the excess handrail next to the first (C67) baluster of the staircase using a hacksaw.
29. Complete the handrail (A14) by securing element A12 using elements C64 and the glue (X01) (fig. 1) (fig. 9).
30. To further stiffen the staircase at intermediate points, secure elements F09 to the wall and join using elements
F33, with the balusters (C81 or C67). Drill using a Ø 8 point and use elements C50, C49, C58, B12 (fig. 11).
31. Determine the length of the bars A28 based on the staircase dimensions and cut them. Insert the bars A28 in
the parts D39-D40 previously assembled on the balusters C67 (fig. 1A) (fig. 3). Join the bars A28 to each other
using the part A41 and the glue provided. Finally, tighten the parts C76 (fig. 1A).
32. Check the linearity of the handrail (A14) and correct using a rubber hammer, if necessary.
Assembling the railing on the landing and the supplementary balustrade
33. Assemble the column (C73) on element G01 protruding from the landing (E02), positioning articles D39 towards
the outside, using elements D49 (fig. 8) (fig. 9) (fig. 1).
34. Position elements F34, using elements C58, B83, B02 on the landing (E02). Drill the landing (E02) using a
Ø 5 mm point, maintaining the same centre to centre distance between the holes as the one used between the
balusters (C67) of the railings assembled before.
35. Position the shorter balusters (C68) and tighten the elements B02 of the articles F34 (fig. 1).
36. Fasten element A15 to the column (C73) using element B02 (fig. 1).
37. Saw off the excess handrail with a hacksaw and complete by gluing element A12 and element C64 with glue
(X01). Secure the handrail (A14) using elements C64 (fig. 1).
38. To stiffen the staircase further at intermediate points, secure elements F09 to the wall and join to the balusters
(C81 or C67) using elements F33. Drill using a Ø 8 mm point and use elements C50, C49, C58, B12 (fig. 11).
39. Determine the length of the bars A28 based on the dimension of the balustrade and cut them (fig. 1).
40. Based on the position and the existence of walls around the opening of the staircase, one or two (C03) extra
balusters may need to be positioned (fig. 9).
41. In this case, consider a space equidistant from the other balusters or from the wall. To secure these, we
recommend drilling the landing (E02) with a Ø 5 mm point and using elements F34, C58, B83, B02. We also
recommend drilling the floor with a Ø 14 mm point and using elements F34, B02, B13 (fig. 10). If necessary,
secure the balustrade on the landing to the balustrade on the floor, (fig. 9), model the handrails carefully,
following well secured curves. Any wrinkles that form on the inside of the handrails are not a defect, rub
energetically (generating heat) with a paper tower until they disappear.
After you have finished assembling the staircase,
please visit our website and send us your suggestions: www.pixima.it
7 - CUBE TUBE PVC