Troubleshooting - Gemini CDX2250 Bedienungsanleitung

Vorschau ausblenden

Inhalt

Inhaltsverzeichnis

Verfügbare Sprachen

the CDX-2250 will be ready to set your next selection. Repeat

the previous steps until you have completed your play list, then

press play to begin the set list.

SINGLE: Pressing the SINGLE button engages SINGLE mode,

in this mode the CDX-2250 will play one song and then stop.

Pressing the SINGLE button again will then activate CONTINU-

OUS mode causing the unit to play continuously (after the last

track, the unit will return to the first track of the disc and con-

tinue to play).

TIME: The TIME button switches the time display between

three available sources, these three are TIME ELAPSED on the

track, TOTAL REMAIN on the disc and REMAIN on the track.

TIME ELAPSED indicates how much time has currently gone

by since the play button was pressed, TIME REMAING ON

DISC will count down the time remaining on the entire disc and

TIME REMAINING ON TRACK counts down the time that is left

before the end of the track.

PITCH: Press the PITCH button to activate the PITCH CON-

TROL SLIDE. Pitch range that can be controlled through the

use of the PITCH CONTROL SLIDER. Press the PITCH button

again to deactivate this mode.

PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE

up or down will change the pitch percentage +/ - 12%.

PITCH BEND: Pushing the PITCH BEND BUTTONS will auto-

matically raise the pitch up to +16% or lower the pitch down

to -16% from the existing pitch setting. Releasing the buttons

will return the pitch to the original pitch setting. You can use

this function to match the beat when mixing from one song to

another.

LOOP SECTION: A LOOP repeats the section between the en-

try point (LOOP IN) and the exit point (LOOP OUT).

A. To set a loop while the unit is playing, start by pressing

the LOOP IN BUTTON (it will light up)

B. When you reach the desired end loop point press the

LOOP OUT BUTTON (it will also light up). The LOOP IN and

LOOP OUT buttons will blink. The loop will continue playing

until you press the LOOP OUT BUTTON again allowing the

music to continue from that point on.

C. To re-engage the loop you must press the RELOOP

BUTTON.

D. When you have released your loop the LOOP IN and

LOOP OUT BUTTON buttons will turn OFF and the will re-

main lit to indicate that your loop is stored in the CDX-2250

memory.

E. Pressing the LOOP IN BUTTON again while the unit is

playing will erase the previously saved loop while saving

your new loop entry point.

F. Press LOOP OUT to exit the loop and save a new com-

plete loop.

G. Press RELOOP to return to the beginning of the previ-

ously saved loop from normal play. Press RELOOP repeat-

edly to cause the loop to stutter.

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT

POINT, WHILE ALL OTHERS WILL BE SEAMLESS.

PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON

causes the operation to change from PLAY to PAUSE or from

PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit

when in PLAY mode, while it blinks in PAUSE mode.

CUE: To set a CUE point, press the PLAY / PAUSE BUTTON

while a file is playing, and use the JOG WHEEL to adjust the

file to a desired point in the track. Pressing the PLAY / PAUSE

BUTTON will set a CUE point. While the unit is playing and after

the cue point has been programmed, pressing CUE will cause

the CD player to enter the PAUSE mode (PLAY/PAUSE BUTTON

blinks) at the programmed cue point (the CUE LED is lit). Hold-

ing down the CUE button changes the function to preview, and

allows you to stutter start or play from the programmed CUE

POINT. Releasing the CUE button will return the CD to the preset

CUE point.

TRACK SEARCH: The TRACK SEARCH buttons let you select

the track to play. +10 allows you to scan through the track selec-

tion in increments of 10.

NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU

MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT.

YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE

CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLY

SELECTED TRACK.