Kärcher WPD 100 Basic Originalbetriebsanleitung Seite 17

Start up
Open the device door
1 Drip pan
2 Device door
3 Release button
 Remove the drip pan.
 Push the unlocking button and open the device
door.
Insert filter
1 Bracket
2 Plate
3 Filter
4 Handle
1 do not touch the marked areas
WARNING
Health risk due to the contamination with germs.
 When replacing the filter cartridges, ensure hy-
giene and cleanliness.
 Do not touch the connections of the socket and fil-
ters.
 Wear sterile disposable gloves when replacing the
filter.
 Do not interchange filters, observe colour coding.
 Remove drip pan and open the device door.
 Turn the filter so that the handle is on the left side
and insert it into the relevant support from the bot-
tom.
1 Marking
 Turn the filter to the right all the way to the stop.
 Check installation position.
The marking on the label on the support and on the
filter must be aligned with each other.
 Close device door and insert drip pan.
Open the door of the base.
The door of the base can be locked.
1 Door of the base.
2 Door lock
 Unlock the door lock.
 Open the door on the support leg.
Insert the CO bottle
2
Note:
Observe general information on handling CO
(see Chapter "Care and maintenance/general informa-
tion on handling CO bottles")
2
1 Rotating regulator
2 Pressure reducer
3 Union joint
4 Main tap
5 Pressure gauge control pressure
6 CO hose
2
 Place the CO bottle in the base and secure it by
2
means of the tie down strap.
 Briefly open the main tap so that possibly present,
liquid CO can escape.
2
 Screw the pressure reducer onto the new gas bot-
tle. Watch for correct mounting of the sealing ring!
 Tighten covering nut firmly.
 Connect the CO hose to the pressure reducer.
2
 Slowly open the main tap on the gas bottle.
 Set 3 bar on the pressure reducer by means of the
control knob.
 Close the main tap on the gas bottle.
 Read the value indicated on the pressure gauge
control pressure.
 The indicated value must remain constant for at
least 5 minutes.
3
-
EN
 With detectable pressure reduction:
Check if the O-ring between the gas cylinder and
the pressure reducer is present and free of dam-
age. Replace defective O-ring.
Check the correct positioning of the pressure re-
ducer.
Tighten covering nut firmly.
Check the hose coupling on the pressure reducer
and the CO hose for visible damage. In case of
2
doubt, call the Customer Service.
 If the pressure reduction cannot be remedied by
the stated measures, the pressure reducer is de-
fective and must be replaced.
 Open main tap.
 Set the operating pressure on the pressure reducer
by means of the control knob.
WPD 100: Presetting 4 bar, re-adjustable if neces-
sary.
WPD 200/600: Set the CO
approx. 3 bar (static) prior to the dispensing of wa-
ter and then check if the pressure is approx. 3.0 bar
during the dispensing of carbonated water (spar-
kling).
 Close the door of the base.
Inserting the 425 g CO
bottles
2
1 Pressure regulator scale
2 Pressure regulator
3 Adjustment wheel
4 Screw connection of the bottle
5 425 g CO bottle
2
 Remove drip pan and open the device door.
 Turn the pressure regulator to "OFF".
 Remove the cover of the CO
 Screw the 425 g CO
connection of the pressure regulator.
 If a resistance can be noticed, turn the 425 g CO
bottle slightly further until it is tightened. A short
hissing noise may be audible.
 Pre-set the pressure regulator to "4".
 Close device door and insert drip pan.
 After initial startup, readjust the pressure on the
pressure regulator in order to achieve the desired
CO concentration in the water.
2
Note:
Regulate strongly spraying water stream during dis-
pensing of carbonated water by lowering the CO
sure. If the water is not sufficiently carbonated, increase
the CO pressure.
2
pressure regulator to
2
bottle
2
bottle.
2
bottle onto the bottle screw
2
2
pres-
2
17