Pioneer VSX-S520D Bedienungsanleitung Seite 53

> Before Start > Part Names
in "AV Adjust" - "MCACC" - "Manual EQ Select" (
Front Left After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (
Center After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (
Front Right After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (
52
> Install > Initial Setup
P40).
/ , adjust the volume of that
P44) matches the
P44).
/ , adjust the volume of that
P44) matches the
P44).
/ , adjust the volume of that
P44) matches the
P44).
> Playback
Surround Right After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (
Surround Left After selecting the speaker frequency from between "63 Hz" and
"16 kHz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 If an item cannot be selected even though connection is
correct, check that the settings in "System Setup" - "Speaker"
- "Configuration" - "Speaker Channels" (
number of connected channels.
0 "63 Hz" can only be selected when this speaker is set to
"Large" in "System Setup" - "Speaker" - "Crossover" (
Subwoofer After selecting the speaker frequency from between "31 Hz" and
"250 Hz" with the cursors
frequency between "-12.0 dB" and "+12.0 dB" with / . (Default
Value is "0.0 dB")
0 This cannot be selected if "No" is set in "System Setup" -
"Speaker" - "Configuration" - "Subwoofer" (
0 The result may not be as expected depending on the input source and listening mode
setting.
0 If you want to make the adjustments while listening to something, press
controller, and select the Preset you want to adjust in "AV Adjust" - "MCACC" - "Manual
EQ Select" ( P40) first.
Advanced Setup | Firmware Update | Others
/ , adjust the volume of that
P44) matches the
/ , adjust the volume of that
P44) matches the
/ , adjust the volume of that
P44).
on the remote
E
N
P44).
P44).