Timer Mode - ThermoPro TP-08 Bedienungsanleitung

BARBECUE temperature is below 220 ºF. It assumes that your BARBECUE is not up
to temperature. Only when the actual BARBECUE temperature goes over 220 ºF, then
falls below 220 ºF, can the alarm be activated, the unit will beep and flash.
Note: The unit will retain your Barbecue & Food alert temperature settings even after the
unit is turned off.

TIMER MODE

Count down
1. Press and hold the LIGHT/MODE button to switch the unit from THERMOMETER
MODE to TIMER MODE. The timer 0:00, with a small icon TIMER will be shown on
the lower part of the display.
2. Press the HI/HR button to set the hour and LO/MIN button to set the minute.
3. Press the START/STOP button to start countdown. The icon "
4. Press the START/STOP button to stop the countdown. The "
5. Press the HI/CLEAR button to clear the setting back 0:00.
Note: The minimum setting for the timer is 1 minute and the maximum setting is 24 hours.
It will be displayed as hours & minutes when the timer does not exceed 10 hours. Once
it exceeds10 hours, only the hour can be displayed. When the countdown reaches "0:00"
the timer starts counting up and it will beep for 30 seconds. The "0:00" and "
blink. Press the START /STOP button to stop the beep.
Count up
1. Press and hold the LIGHT/MODE button to switch the unit from THERMOMETER
MODE to TIMER MODE. The timer 0:00, with a small icon TIMER will be shown on
the lower part of the display.
2. Press the START/STOP button to start count up. The icon "
3. Press the START/STOP button to stop the count up. The "
4. Press the HI/CLEAR button to clear the setting back to 0:00.
Note: When the count up timer reaches 9:59, it will keep displaying as 9:59,
the unit beeps with the " " icon blinking for 30 seconds.
Note: The unit will retain your timer settings even after the unit is turned off.
Temperature Unit Display
Press and hold the /ºF/ºC button for 2 seconds on the receiver to select temperature
display in ºF or ºC.
Press and hold the ºF/ºC/ button for 2 seconds on the transmitter to select temperature
display in ºF or ºC.
" will blink.
" will be solid.
" will blink.
" will be solid.
meanwhile,
-6-
Using TIMER MODE & TEMPERATURE MODE simultaneously
The TIMER MODE and TEMPERATURE MODE can be used simultaneously. This allows
you to monitor the temperature for both FOOD and BABECUE in the TEMPERATURE MODE
when using the TIMER MODE to keep track of another cooking task. You can tell different
task by the alarm sound as well as the icons.
1. In the THERMOMETER MODE, when the temperature is reached, the receiver will
alarm you by beeping once every second for the BARBECUE/oven/smoker temperature
and beeping twice every second for the FOOD temperature. The alarm icons and probe
temperature will blink along with the alarm sound.
2. In the TIMER MODE, when the timer is reached, the receiver will alarm you by
3 times in every second. Either the upward arrow (for count-up) or downward arrow (for
countdown) will blink.
Procedure for typical use in an outdoor BARBECUE
The following examples will go through the steps to have this professional remote cooking
thermometer alarm you if a piece of meat (Boston Butt) is cooked to 160 ºF and if your
barbecue temperature falls below 225 ºF or goes above 250 ºF, and reminds you to check
the smoker in 2 hours.
" will
Set up BARBECUE
Follow the synchronization/pairing procedure to pair the receiver and transmitter.
Place meat on the BARBECUE grill rack.
Insert FOOD probe sensor into the center of thickest portion of the meat. Avoid
touching bone or heavy fat areas.
Clip the special BARBECUE probe to grill rack of barbecue chamber.
Position the probe sensor wires so they will not come into contact with flames and
exit the barbecue without being pinched/ crushed by the cover.
Stand/ hang the transmitter away from heat source of barbecue. DO NOT put transmitter
on closed cover or under the cover. The transmitter is water proof for use in rain.
In THERMOMETER MODE
Press HI/CLEAR to display the maximum FOOD temperature.
Press and hold HI/CLEAR until the maximum FOOD temperature flashes.
Press HI/CLEAR repeatedly until 160 ºF appears (press and hold HI/CLEAR button
will increase the temperature 10 degrees per second).
Quickly press LIGHT/MODE to confirm the 160 ºF setting.
Press HI/HR to display the maximum BARBECUE temperature.
Press and hold HI/HR until the maximum BARBECUE temperature flashes.
Press HI/HR repeatedly until 250ºF appears (press and hold HI/HR button will increase
the temperature 10 degrees per second)
-7-
beeping