Helpful Hints; Using The Timer - ThermoPro TP-11 Bedienungsanleitung

NOT use in the rain.
7. Press MEAT so BEEF is displayed.
8. Press TASTE so MEDIUM is displayed and 150 F will be shown as the TEMP SET.
9. Press MODE to change to timer mode.
10. Press MIN 5 times to set for 5 minutes so that 0:05 is displayed. Press START
/STOP to start the countdown. Press MODE to go back to thermometer mode.
11.You may take the receiver up to 300 ft away from the outdoor grill.Go indoors
if desired.
12. When 5 minutes are up the receiver will beep for 60 seconds.
13. When the temperature of probe in the steak reaches 55 F the LCD backlight
will flash blue.
14. When the temperature of probe in the steak reaches 135 F the LCD backlight
will flash green.
15. When the temperature of probe in the steak reaches 150 F MEDIUM the
receiver will beep and the LCD backlight will flash red.
16. Press STOP to turn off the alert.
17. Turn off grill. Remove the probe sensor from steak. Always wear a heat resistant
glove to touch the stainless steel probe sensor or wire during or just after
cooking. Do not touch with bare hands.
18. Clean the stainless steel probe and dry thoroughly after each and every use.
19. Turn off the transmitter and receiver.

HELPFUL HINTS

If the receiver and/or the transmitter display LLL or HHH instead of the probe
temperature, wait for probe to reach room temperature. If LLL or HHH is still
d i s p l a y e d , i t i s l i k e l y t h e i n t e r n a l p r o b e w i r e h a s s h o r t e d o u t e i t h e r t h r o u g h
moisture or heat damage.

Using the Timer

Count down
1. Press MODE to select timer mode. The upper display will show a small TIMER
and 0:00.
2. Press HR and MIN button to set the timer. Press START/STOP button to start
countdown. " " will blink for every second.
3. To stop the countdown process , press START/STOP button. The "
solid.
4. Press HR & MIN buttons together to clear the setting back to 0:00.
Note: The minimum setting for the timer is 1 minute. When the timer counts
°
°
°
°
" becomes
-6-
d o w n b e l o w 1 h o u r 1 : 0 0 t h e d i s p l a y w i l l c h a n g e t o 5 9 ' 5 9 " t o i n d i c a t e , 5 9
minutes 59 seconds. The seconds will be shown counting down then. When the
countdown reaches 0'00" the timer starts counting up and it will beep for 60
seconds. The timer and " " will blink. Press the START/STOP button to stop
beeping. When the count up reaches 23:59:59 (59 seconds are not displayed)
the display will turn to 0:00, the unit beeps and "
Count up
1. Press MODE to select timer mode. The upper display will show a small TIMER
and 0:00.
2. Press START/STOP button to start count up. The "
3. To stop the count up process , press START/STOP button. The "
solid.
4. Press CLEAR button to clear the setting back to 0:00.
HELPFUL HINTS
Do not immerse the probe in water while cleaning.
Do not allow the probe or probe wire to come into contact with flames. If cooking
with grill cover closed, only use medium or low heat.
If the probe becomes defective within 90 day warranty period please return
defective probe to address below along with return address and we will send
you new probe no charge.
If the temperature displayed seems to read too high or the temperature seems
to increase too quickly check to make sure the probe tip is not poking through
the food. Reposition the probe tip in the center of the thickest part of food. Avoid
touching bone or heavy fat areas.
Cautions
Always wear a heat resistant glove to touch the stainless steel probe sensor
or wire during or just after cooking. Do not touch with bare hands.
Keep the stainless steel probe sensor and wire away from children.
Not Intended for Use by Persons ages 12 and Under.
Clean the stainless steel probe and dry thoroughly after each and every use.
Do not immerse the probe or wire in water. Clean using a damp, soapy cloth.
Do not use the receiver or transmitter in the rain. They are not waterproof.
Do not expose the plug of the stainless steel probe or the plug in hole of the
transmitter to water or any liquid. This will result in a bad connection and faulty
readings.
Do not expose the receiver or transmitter to direct heat or surface.
Do not use stainless steel probe in microwave oven.
" will blink for 60 seconds.
" will blink for every second.
" becomes
-7-