Honeywell HDE020E Betriebsanleitung Seite 5

ENGLISH
You can reset continuous run function and switch to Humidistat
function by pressing the humidistat button .
If you want to switch back to continuous mode again, press continuous
mode button .
Note: if unit is switched off, all user settings will be erased.
HUMIDISTAT AND ADVANCE HUMIDITY CONTROL
SYSTEM
The unit will run automatically until the desired humidity is reached.
Once reached, the compressor will shut off automatically. The fan will
continue to run until the unit is either powered OFF manually, or the
selected timer duration is completed, this function allows for more
accurate humidity detection and efficient use of the compressor.
Choose the humidity % by pressing the key until the desired %
(80; 70; 60; 50; 40 %) shows in the display.
5 seconds later, display will indicate current ambient humidity.
You can set the timer function while the unit is under humidistat mode:
Press the timer button repeatedly to select the desired number
of hours. The unit will switch off automatically once the selected
amount of time has elapsed. If you need to reset the timer function,
press the timer button repeatedly until all 3 LED indicators
, are off.
You can reset continuous run function and switch to Humidistat
function by pressing the humidistat button .
If you want to switch back to continuous mode again, press
continuous mode button .
Note: Under humidistat mode, when timer function is on, the unit
will switch off automatically once time has elapsed even if desired
humidity is not reached.
If the Continuous mode is selected the unit will work independently
of the ambient humidity.
Note: if unit is switched off, all user settings will be erased.
AUTO DEFROST
When the Temperature is approaching 10 °C, the Auto Defrost function
will be activated automatically; the LED indicator (e) will turn on
in yellow. The unit will automatically operate the auto defrost cycle:
The compressor will stop for 8 minutes and then run for 24 minutes,
repeatedly. The fan will run all the time to defrost.
DRAINAGE INSTRUCTIONS
(see page 5)
1. WATER TANK
• When not using the water hose, the water will drain into
the tank at the rear of the unit. As soon as the tank is full,
the light (f) will illuminate in red and the compressor
will shut off automatically, the unit will enter stand-by mode.
The tank should be emptied (fig. 2) and replaced (fig. 3)
and then the unit will restart automatically.
• If the control lamp (f) does not go off, pull the water tank (6)
out again (fig. 1).
8
• Check that the swimmer (8) is correctly installed. The swimmer
must not be removed, because otherwise the automatic
interruption of the dehumidifying operation is not guaranteed.
Overflowing water can damage objects and floor coverings
or cause an electric shock.
Note: To prevent compressor from breaking down due to interrupted
starting, Please refrain from repeated removal and reinsertion
of the water tank.
2. CONTINUOUS DRAINAGE
• To use the continuous drainage function, remove the water
tank (fig. 1) and attach the water hose (9) to the drainage
hole (7) as shown in diagram (fig. 4). Ensure a tight fit to avoid
water leaks. Replace the water tank as per diagram (fig. 5-6).
• Do not drain water continuously if there is a possibility that
temperature around the hose could drop to freezing point.
Water inside the hose may freeze and prevent the water
in the drainage tank from flowing out. The water may leak
from the unit and damage surrounding objects.
• When using the unit after it has been stored for a long period
of time or when draining water continuously for a long time
with no assistance, check the unit periodically for foreign objects,
,
etc, that could clog the pipes resulting in heat generation and/
or a water leakage.
Note: when using the continuous drain feature, make sure the drain
tube is laid flat horizontally and fastened in place; avoid overlapping
or depressing, and make sure it lays lower than the drain hole.
MAINTENANCE
• Before performing any maintenance or cleaning of the dehumidifier,
always switch off and unplug the appliance.
• Use a soft cloth when cleaning the appliance.
• Do not spray the dehumidifier with water.
• Do not use harsh chemicals, gasoline, detergents, chemically
treated clothes, or other cleaning solutions. These items and
chemicals may cause damage to the dehumidifier cabinet.
• To clean the filter (fig. 7), use a vacuum cleaner or tap the filter
lightly to remove dust and dirt. If the filter is unable to be cleaned
by vacuum, use warm water with a small amount of medium
strength detergent.
• Remove the water tank (fig. 1) and ensure the drainage outlet
is clear of obstructions. If continuous drainage is used, check
outlet hoses are free of kinks and obstructions.
STORAGE
If the dehumidifier will not be used for an extended period of time,
turn the appliance off and unplug from the main Power source.
Tidy the power cord. Completely empty the water tank and wipe it
clean. Cover the dehumidifier and store in a dry location not in direct
sunlight.
DISPOSAL
This symbol on the product or its packaging indicates that
the appliance cannot be treated as normal domestic waste,
but must be handed in at a collection point for recycling
electric and electronic appliances.
Your contribution to the correct disposal of this product protects
the environment and the health of your fellow men. Health and
the environment are endangered by incorrect disposal. Further
information about the recycling of this product can be obtained
from your local town hall, your refuse collection service,
or in the store at which you bought the product.
WARRANTY/CONDITION OF PURCHASE
As a condition of sale, the purchaser assumes responsibility for
the proper use and care of this appliance in accordance with these
printed instructions. The purchaser or user must judge himself or
herself when to use the appliance and the length of use. Please
keep your receipt (or invoice) as your proof of purchase. The receipt
must be always presented when making a claim under the warranty
period. You may also be asked to provide the LOT number which gives
you the production date of your product. The LOT number is located
on the product and on the packaging. The production date can be
deciphered as follow: The first 3 numeric digits after LOT represents
the day of manufacture. The next 2 numeric digits represent the last
two digits of the calendar year of manufacture and the letter(s)
at the end are a factory identifier (E.g.: LOT No.: 12313 ABC this product
was made on the day 123, year 2013 at the factory code ABC).
NOTE: IN THE UNLIKELY EVENT THAT YOU EXPERIENCE A
PROBLEM WITH THIS PRODUCT PLEASE FOLLOW THE WARRANTY
INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO REPAIR THIS
PRODUCT YOURSELF. DOING SO WILL VOID THE WARRANTY AND
COULD CAUSE PROPERTY DAMAGE OR LEAD TOPERSONAL INJURY.
Technical modifications reserved.
This product carries the CE mark and is manufactured in conformity
with the Electromagnetic Directive 2004/108/EC, the Low Voltage
Directive 2006/95/EC and the RoHS Directive 2011/65/EU.
HDE020E
220–240 V ~ 50Hz
340W
ENGLISH
9