Useful Tips For Recording; Monitoring The Input Signal; Adjusting The Recording Level; Assigning Track Numbers During Recording - Tascam MD-350 Bedienungsanleitung

Useful Tips for Recording

Buttons used on this page

Monitoring the Input Signal

You can monitor the input signal of the
component connected to each input
terminal before recording.
ø
1. Press the [ EJECT] button to eject the
disc.
2. Select the input source with the [INPUT
SELECTOR].
º
3. Press the [ RECORD] button.
("Monitor Mode" appears.)
... Even when the [REC MODE] is set to
[MONO], the output is sent to both
channels.
... Insert an MD or press the [
button to cancel the Monitor mode.

Adjusting the Recording Level

ª
Recording an analog signal
1. Insert a recordable MD and press the
º
[ RECORD] button to enter the Record-
Ready mode (" " lights up).
2. Play the highest-level section of the
program source and turn the [INPUT]
control so that the "OVER" segments of
the peak level meters do not light.
3. Play the program source again.
... Press the [
¥ π
PLAY] or [ READY] button
to start recording.
ª
Recording a digital signal
1. In Record-Ready mode, press the
[EDIT/NO] button until "D-LEV 0.0dB"
appears.
µ ≤
2. Turn the [ TRACK ] dial to adjust
the recording level. The recording level
can be set in 0.5 dB steps within a range
between -6.0 dB and +6.0 dB.
3. Press the [YES] button after making the
adjustment.
Assigning Track Numbers During
Recording
Assigning track numbers at specific points
will make it easy to quickly locate those
points later using the playback or editing
functions.
ª
To assign track numbers automatically
(Auto Track function)
Track numbers can be assigned automati-
cally during recording by setting the Auto
Track function to ON.
1. In the Record or Record-Ready mode,
ª
STOP]
press the [EDIT/NO] button until
"A_TRACK > XXX" appears.
µ
2. Turn the [
"A_TRACK > ON".
3. Press the [YES] button to end the setting
function.
... While the Auto Track function is "ON",
the signal level must remain low for 4 or
more seconds before a new track
number is advanced.
... During digital recording from a CD or
MD, the track numbers are advanced
automatically according to the CD or
MD data.
... Once the Auto Track function is "ON",
this mode will not be released even after
the power is turned off.
Press the [YES] button after selecting
"A_TRACK > OFF" to release it.
ª
To assign track numbers manually
º
Press the [ RECORD] button at every point
where you want to assign a track number
during recording. Each press of the button
advances the track number.
ª
To assign track numbers after recording
A track number is added when a track is
divided in editing. (See "Dividing a track" on
page 16.)
Note:
Changing the input with the [INPUT
SELECTOR] switch during recording
activates the Record-Ready mode.
≤
TRACK ] dial to select
– 11 –
Recording Over Existing Tracks
(Over Write)
The Over Write function allows you to
record music by erasing a previously
recorded track.
1. Perform steps 1 to 4 of "Recording an
MD" on page 8.
µ ≤
2. Turn the [ TRACK ] dial (or press
µ ≤
the [ TRACK ] buttons on the
remote control unit) until the track
number to be recorded over appears.
º
3. Press the [ RECORD] button ("
lights up).
... After "Over Write" appears, the remain-
ing recording time is displayed.
... The track numbers which come after the
track being recorded over blink on the
music calendar.
4. Adjust the recording level.
... If [ANALOG] was selected above, adjust
the recording level with the [INPUT]
control.
¥
5. Press the [ PLAY] button or [
button to start recording.
... The deck records over the existing
track. The track number is updated.
ª
Recording over an existing track from
the middle
1. Select the track number to be erased
¥
then press the [ PLAY] button to start
playback.
π
2. Press the [ READY] button where you
want to start recording.
º
3. Press the [ RECORD] button.
... The track number is updated and blinks
on the music calender.
¥ π
4. Press the [ PLAY] or [ READY] button
to start recording.
... The deck records over the existing
track.
[CAUTION]
... It is not possible to record from the
middle of an existing track when
" " or "
"
π
READY]
" is lit.