The Remote Control; Before Operating; Setting Up The Device - Block SR-100 Bedienungsanleitung

Remote control
1.
2
1
3
2.
5
4 6
3.
7
8
4.
9
13
10 12
5.
6.
11
7.
13
14
15
8.
16 17
9.
18
10.
11.
12.
19 20
13.
14.
15.
16.
17.
18.
19.
20.
40
„Standby" button: switches the device to „Clock" mode, the display
will show the time and the date. To save energy, switch off the device
in the net counter.
„Mode" button : By pressing, the display switches to the overview
mode. You can now use the multifunction knob or the arrow keys on
the Remote control select the music source
„Mute" button: switches the sound off.
Taste „Menu/Info": One or more short presses will display additional
information about the music source (if any) on the display. Long press
calls up the menu of the device.
„Volume +" button: increases the volume
„Volume -" button: reduces the volume
„Back" button: on radio mode, the device searches the previous lo
wer transmitter. On CD and media player mode, the unit jumps to the
previous track.
„Forward" button: on radio mode, the device searches the next higher
transmitter. On CD and Media Player mode, the device jumps to the
next track.
Arrow upwards: on FM mode to increase the frequency in 0.05 MHz . In
menu to select the different points.
Arrow to the left: to reach the previous setting in the menu.
Arrow down: in FM mode by the frequency in 0.05 MHz increments to
reduce. To select the different points in the menu.
Arrow to the right: to access selected functions in the menu.
"Play" button
„Stop" button.
„FOLDER UP" button: Only for CD operation on MP3 CDs with folder
structure.
„FOLDER DOWN" button: Only for CD operation on MP3 CDs with folder
structure.
Taste „REPEAT/RANDOM": Press once to start the repeat function for
the current title, press the repeat function twice whole media (for
example, CD, USB, media server) a third press ends all Repeat. Long
press starts the playback of the entire medium in random Sequence,
pressing again for a long time ends this function. Watch out for the
displays at the bottom of the display.
Button „1 - 10": on radio mode, recalls on the stored transmitters
and on CD mode, it chooses the single pieces of the CD.
T„P" button: recalls or saves pre-set transmitters in radio mode.
„CD" button: ejects the CD.

Before operating

Before you can use your Internet radio, the streaming functionality or the operation via smart phone app, you need:
1. A fast internet connection.
2. A router, preferably with WLAN (wireless access point).
3. In case your router does not provide WLAN connection, you also could connect your equipment using
Ethernet cable.
4. Later, when setting up the device, you choose between wireless (WLAN) and cable connection.
5. If your wireless network is protected with Wired Equivalent Privacy (WEP) or with Wi-Fi Protected Access
(WPA), you will need a WEP or a WPA code, so that your Internet radio can be connected to the router.
6. Before proceeding, make sure that your wireless network is turned on and has a broadband internet
access.
7. In case of problems while connecting your device to the router, please try to solve them using the manual
instructions of the router.

Setting up the device

1. Connect the FM and DAB + telescopic antenna to the device. Then pull the telescopic aerial to full length.
Later, when setting up your channels, you can optimize the reception quality just changing the angle of
inclination and the tilt angle of the aerials.
2. If you want wirelessly to connect your SR-100 to the Internet via an existing wireless Network, please
mount the included WLAN antenna
3. If you want to connect your SR-100 to the Internet via Ethernet (wired), please connect your router to the
Ethernet jack of the SR-100 using a RJ-45 cable.
4. Connect the connection cable of the enclosed power supply unit to the device and plug this into a power
outlet
41