Displaying Subtitles; Teletext; Sleep Timer; Troubleshooting - Silvercrest SSR 1080 B2 Bedienungsanleitung Und Serviceinformationen

the characters selected. The left window will only show the channels matching the character sequence entered. You can use the [Red] button (39) to
delete the entire entry or the [Green] (38) button to delete one character. As soon as you see the desired channel press the [Yellow] button (23) to
skip to the left window where you can select the channel.

Displaying Subtitles

Some programmes are broadcast with subtitles, for instance for the hearing-impaired or in different languages. Press SUB (38) to open the subtitle
selection. Note: DVB subtitles are rarely broadcast and differ from common Teletext subtitles.

Teletext

Many channels broadcast additional information and services. Teletext pages are like "electronic magazines" allowing you to view news, sport,
weather information, special offers and much more. The availability and content depends on the channel provider. The start or Index page is always
page 100. On this page, you will find an overview of the other pages. Press the TEXT button (22) to launch the Teletext view. To enter a page number,
always use 3 digits on the numeric buttons (20) or use the coloured special function buttons (22, 23, 38 and 39). The function currently assigned to
these control buttons appears at the bottom of the Teletext window. Pressing the STATUS button (32) several times changes the transparency of the
Teletext window. Press EXIT (24) to exit the Teletext pages.

Sleep Timer

You can use the SLEEP button (23) to set an automatic power off countdown. Pressing the SLEEP button (23) several times changes the countdown or
disables the sleep timer. The following options are available: "10 min", "20 min", "30 min", "1 Hour", "1 Hour 30 min", "2 Hour" and "Off".

Troubleshooting

No signal
No signal is shown on the device or on the OSD menu signal indicators.
1. First check the antenna cable: The braided lead of the external wire and the aluminium film must have good contact with the F connector and must
not touch the inner (centre) wire!
2. Check the reception settings and edit them if necessary. To further locate the problem we recommend that you temporarily connect the LNB directly
to the receiver and do not use any switches or splitters.
Functional fault
1. The device shows the wrong broadcasting times in the EPG or shows the wrong time. Once powered up, the satellite receiver needs to read and
process the channel data. Depending on the transponder, this can take some time. Sometimes it may be necessary to re-open the EPG or to
change the channel.
2. The device fails to respond. Unplug the power cord or switch the device off using the main power switch (16). Wait several seconds and reconnect
the device to try again.
Small number of channels
1. Make sure that you have enabled the correct Channel List. Press the OK/ENTER button (25) to open the programme list. The first line shows the
channel list currently selected. To select a different channel list, press the [Red] button (39). Press /P+ or /P- navigation buttons (26) to select
the desired channel list and press the OK/ENTER button (25) to confirm. To obtain the entire channel list, select the "All TV" or "All Radio" group
and press the OK/ENTER button (25) to confirm. To close the group and channel list, press the EXIT button (24) as many times as necessary to
hide all windows.
2. The antenna has been moved to the wrong satellite. When positioning the antenna you may receive satellite broadcasting on similar frequencies
which causes the signal indicators on your satellite receiver to go up. When you switch channel, suddenly foreign channels or the message "No
Signal!" appear. Normally, you just need to move the antenna a few degrees East or West to receive the channels you want.
No sound, distorted sound
1. If there is no sound or only interference, your TV set or AV receiver may not be capable of decoding Dolby Digital/AC3 audio via the HDMI port.
Solution: Press the AUDIO button (39) to select Stereo sound. If the channel does not transmit stereo sound, connect the digital S/PDIF audio
output (9) to your Surround/AC3/Dolby Digital sound system.
2. If there is no sound, check whether the MUTE function has been enabled. If the sound is muted, press the MUTE button (17) again to resume the
sound output.
3. If the sound is very low or there is no sound at all, double-check the volume setting and, if necessary, increase the volume via the /VOL+
navigation button (26). Please also check the volume setting on your TV set or your hi-fi amplifier, if one is connected.
Satellite Receiver SSR 1080 B2
English - 33